A rigid cylinder is filled with refrigerant-134a at 18°C. At this state, 40 percent of the mass is vapor. A valve at the bottom is opened, and refrigerant is withdrawn outside. Heat is transferred to the tank such that the temperature in the tank remains constant and the refrigerant fills the tank all the time (V1= V2). Determine the amount of heat that must be transferred by the time one-fourth of the total mass has been withdrawn. The tank volume is 0.1-m3

Q: during the process from the initial temperature of (30×1.6)°C down to the final temperature of 20°C.…

A:

Q: done during the process is

A:

Q: Use image below PART C- Evaluate the useful work (i.e., the work corrected for the work against the…

A:

Q: A frictionless piston-cylinder device as shown in Figure Q4 contains 8.5 liters of saturated liquid…

A:

Q: Air enters a diffuser in order to decrease its pressure from 65 kPa to 45 kPa. At the inlet, its…

A: Given data: The inlet pressure of the air to the diffuser is p1 = 65 kPa. The outlet pressure of…

Q: A rigid tank of volume 10 m³ initially contains saturated water vapor at a temperature of 120 °C.…

A:

Q: Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed…

A:

Q: stream of water (4 kg/s; T = 50ºC) is continuously mixed with another stream of water (1 kg/s; T =…

A: Given:m1=4 kg/sT1=50°Cm2=1 Kg/sT2=80°CQa=50 KJ/Kg

Q: Determine the total work done by a gas system following an expansion process as shown in Figure…

A: Given Gas system To find Total work done

Q: A piston-cylinder assembly contains 3 lb of water vapor, initially at 300F and 20 lbf/in2 is…

A: To find (a) The total work done during the process W. (b) The total change in entropy during the…

Q: PROBLEM # 2 A piston-cylinder containing 12 Ib of air receives heat at a constant temperature of…

A: Given, Constant temperature, T=900.6 0R Mass of the air, m=12 lb The initial pressure, pi=29…

Q: Two boilers one with superheater and another without superheater are delivering equal quanttes of…

A: Given Data: The pressure of boiler, P1=P2=20 bar The pressure of the main, P3=20 bar

Q: Two tank are connected, as shown in the figure below, both containing water. Tank A contains 0.5 kg…

A:

Q: A piston-cylinder assembly contains R-134a refrigerant in a volume of 0.15 m3, 0.28 MPa and 40 ° C.…

A: Given data, Process 1-2 :- According to the question, a pin fixed the piston at a point. Now, the…

Q: A 10-kg steel container (cp = cv = 0.46 kJ/(kg K)) is cured at 500 °C. After coming out of the oven,…

A:

Q: Water, initially a saturated liquid at 100°C, is contained in a piston-cylinder assembly. The water…

A:

Q: 3. A room is to be heated by 1000 kg of a liquid contained in a tank placed in the room. The room is…

A: The mass of the liquid is m=1000 kg The final temperature of the liquid is Tf=25°C=298 K The heat…

Q: Question 1 A mass of 0.7 kg of air undergoes two reversible processes in a piston-cylinder device as…

A:

Q: Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed…

A:

Q: Saturated steam at 329.3 degree Celsius undergoes an isentropic process until it reaches a pressure…

A: Given Data The temperature of the steam is T=329.3°C=602.3 K.  The pressure of the steam is P=1.6…

Q: An adiabatic compressor receives 0.5 kg/s of helium at 175 kPa and 320 K and discharges it at 0.8…

A:

Q: Solve for the heat added (in Btu) in the process

A: The mass of the water mw=5 kg The initial pressure of water P1=200 kPa The initial specific volume…

Q: Two lbs of water vapor in a piston-cylinder assembly expands at a constant pressure of 250 lbf/in²…

A: Givenm=2lbsP=250lbf/in2  at saturated vapourV=7.08 ft3

Q: The boiler of a steam generator has a total volume of 2 m3, and initially contained 1.5 m3 of water…

A: Given,   P1 = 1 kgf/cm2 = 0.098 MPa;  P2 = 56 kgf/cm2 = 5.491 MPa; V = 2 m3 Volume of water = 1.5 m3…

Q: HW5: A 20-m3 tank contains nitrogen at 25°C and 800 kPa. Some nitrogen is allowed to escape until…

A: Given Data- Initial properties P1=800KPa ,T1=25'C , V1=20m3 Final Properties P2=600KPa , T2=20'C ,…

Q: Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed…

A:

Q: Refrigerant -134a at 200 kPa and 40 C flows through a refrigeration line. Determine its specific…

A: Given: The pressure of the refrigerant is P=200 kPa. The temperature of the refrigerant is T=40°C.

Q: Is it true during an adiabatic process, a system exchanges no heat with its surroundings. If it is…

A: The given statement is true. During an adiabatic process, there is no heat exchange between the…

Q: A gas cylinder with interior volume 11.6 L holds compressed air at 17.4 MPa. The cylinder is joined…

A: Given: Volume of the gas cylinder: →V1=11.6 L=0.0116 m3 Pressure in the gas cylinder: →P1=17.4 MPa…

Q: Problem 08.034 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS - Refrigerant Constant Pressure…

A:

Q: A rigid tank of 0.22-m'volume initially contains saturated vapor refrigerant-134a at 1.2 MPa. The…

A:

Q: Saturated liquid water, initially at 25°C contained inside a tank, is then delivered by a pump at 5…

A:

Q: A piston-cylinder device initially contains air at 150 kPa and 27°C. At this state, the piston is…

A: To know the behavior of gases on various conditions, various assumptions are made because, in real…

Q: A piston-cylinder device has a 2 kg refrigerant R-134. The piston, which has a diameter of 20mm and…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.