A reinforced concrete T-beam has the following properties: beff=1340mm, tf=150mm, bw = 300mm, d=610mm, Asbot= 9260mm2, fc'=28MPA, fy=414 MPa. Calculate the nominal moment capacity of the section for positive bending in kN-m. Express your answer in 2 decimal places.

A reinforced concrete T-beam has the following properties: beff=1340mm, tf=150mm, bw = 300mm, d=610mm, Asbot= 9260mm2, fc'=28MPA, fy=414 MPa. Calculate the nominal moment capacity of the section for positive bending in kN-m. Express your answer in 2 decimal places.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Related questions

Q: Use bonded tendons as prestressed reinforcement. Determine the nominal moment strength. (kN-m)

A: Given Data: The data are given as: fc' = 35 MPafpu = 1500 MPaAps = 1800 mm2fpy = 1320 MPa To…

Q: Q1: A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1. Using…

A: F'c=21 MPaFy=420 MPan=10 Working stress methodσb=213=7MPaσs=230 MPa…

Q: The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the…

Q: f) the maximum bending moment in the beam. Enter your answer in kNm to 3 decimal places.

A: Given figure is a simply supported beam. Point load = 3.3 kN, acting at the midspan. Total span…

Q: Select a standard rolled steel I-section for the simply supported beam shown in Figure. A factor of…

A: NOTE - Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w…

Q: A simply-supported beam is subjected to a loading resulting in the bending moment diagram shown. The…

A: The maximum bending stress is given by: σc max=M×yI M = Maximum compressive bending moment y =…

Q: P = L1 = L2= L1 Your Answer: P 195 2.50 4.5 Answer KN m m L2 ▷ View hint for Question 1 P The…

Q: P = 9 kip 2 in. 1 in. 1.5 ft The aluminum post shown in the figure is reinforced with a brass core.…

Q: a) Is the beam properly reinforced/over-reinforced/ balanced Determine the factored moment…

A: RC Singly beam,b=500 mmD=700 mmd=600 mmf'c=48 MPaReinforcement: 3-30Mfy=400 MPaφc=0.65φs=0.85Es=2…

Q: The composite beam shown in the figure is simply supported and carries a total uniform load of 50…

A: From The above information, we have to calculate the following Modulus ratio is calculated by…

Q: A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

A reinforced concrete T-beam has the following properties: beff=1340mm, tf=150mm, bw = 300mm, d=610mm, Asbot= 9260mm2, fc'=28MPA, fy=414 MPa. Calculate the nominal moment capacity of the section for
positive bending in kN-m. Express your answer in 2 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.