A reinforced concrete simply supported beam having a length of 8m, has carries a 385 kNm factored moment. Steel covering is 50mm. Using fc’ = 28 MPa and fy = 415 MPa. a. Determine the most possible height if the beam carries partitions. b. Determine the minimum width of the beam. c. Determine the maximum width of the beam.

A reinforced concrete simply supported beam having a length of 8m, has carries a 385 kNm factored moment. Steel covering is 50mm. Using fc’ = 28 MPa and fy = 415 MPa. a. Determine the most possible height if the beam carries partitions. b. Determine the minimum width of the beam. c. Determine the maximum width of the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design of Concrete beam A rectangular beam has a width of 375mm and has an effective depth of 450 mm. f'c = 25 MPa, Fy = 300 MPa. 1. Determine the moment capacity if it is reinforced with steel area in tension w/ 12-25mmø reinforcement bar. Use 0.9 as moment reduction factor. 2. Determine the depth of stress block if steel in compression As' = 3000 mm² is added with steel covering of 50 mm below the top of the beam. 3. Determine the moment capacity of the beam reinforced for tension and compression. 375 0.85fc' 0.003 450 12-25mm0 bar N.A 265.74 (d-an) T= As Sy Es 184.26
A rectangular beam has a width b = 300 mm, and effective depth d = 500 mm and a total height h = 550 mm. The beam is reinforced with three bars ᶲ 20 mm. Compute the nominal strength of the beam cross section Mn and the design moment Mu. Use f’c = 35 MPa and Fy= 420 MPa.
2. The section of a reinforced concrete T-beam has d= 400mm, bf = 750mm, t= 100mm, bw 300mm. The beam is reinforced with 7 pcs of 32mm rebars with Fy = 415MPA concreto has F'c = 28MPA. Dotermine the safo ultimato moment capacity of the beam.
Design the beam to resist the loads shown using WSD Method. Take fc = 9 MPa, fs = 124 MPa, n= 11, bar diameter = 20 mm. Take b = d/2
The joist AB used in housing construction is to be made from 8-in. by 1.5-in. Southern-pine boards. The design loading on each board is placed as shown in the figure below. The allowable bending stress for the wood is Jallow 1.5 and the allowable shear stress is Tallow = 180 psi. Assume that the beam is simply supported from the walls at A and B. (Figure 1) Figure 1 ▾of 1 8 in. 150 lb L 150 lb L 150 lb L 1.5 in. Determine the largest room width I that the boards can span. Express your answer to three significant figures and include the appropriate units. L = 32.0 Submit μA ft My Answers Give Up ? Incorrect; Try Again; 3 attempts remaining
Determine the positive nominal flexural strength Mn of the T-beam in the figure below. Assume fc′ = 21MPa and fy = 420MPa Determine the effective width of the flange if the clear spacing of the beams is 2m while the clear span length of the beam is 3m. Determine the Nominal Moment Capacity of the beam considering that the diameter of stirrup is 10mm and the concrete cover is at 40mm.
1. The section of a reinforced concrete T-beam has d = 400mm, bf = 800mm, t = 100mm, bw = 300mm. The beam is reinforced with 8 pcs of 32mm rebars with Fy = 415MPA concrete has F'c = 28MPA. Determine the safe ultimate moment capacity of the beam.
Please explain all options..
the floor framing plan of a reinforced concrete building. All beams are 300 mm x 600 mm. The properties are as follows: slab thickness = 100 mm; super imposed dead load = 3 kPa; live load = 4.8 kPa; concrete unit weight = 24 kN/m3. The columns at E and H are deleted thus girder BEHK alone supports beam DEF at E and beam GHI at H. Calculate the uniformly distributed service dead load at beam DEF in kN/m Calculate the uniformly distributed service live load at beam DEF in kN/m.
need asap please
Please answer situation 2 only
Need help asap pls.