A pump has a 100 mm diameter suction pipe and a 75 mm discharge pipe. The capacity is 15 L/s of water. A water-mercury manometer is installed in the inlet which reflects a vacuum pressure of 198mm of Hg. The mercury level on the suction side is 100 mm below the pipe centerline. The pressure gauge 200 mm above the pump inlet recorded a pressure of 0.95 bar. The measured input powe was 3.2 kW. Find the efficiency of the pump. Select the correct response(s): 75.12 % 60.42 % 59.01 % 80.43 %

A pump has a 100 mm diameter suction pipe and a 75 mm discharge pipe. The capacity is 15 L/s of water. A water-mercury manometer is installed in the inlet which reflects a vacuum pressure of 198mm of Hg. The mercury level on the suction side is 100 mm below the pipe centerline. The pressure gauge 200 mm above the pump inlet recorded a pressure of 0.95 bar. The measured input powe was 3.2 kW. Find the efficiency of the pump. Select the correct response(s): 75.12 % 60.42 % 59.01 % 80.43 %

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need help drawing a pictoral of this shape which has the front, top, and side view. Can you sketch it out on some paper ?
Just a small explanation only please and the correct answer thanks.
I want you to draw HGL& EGL For the first picture using the same method on the second picture
Q1: write a program to enter any text and compute its length. Q2: Design a form with a text box. Use select statement so that when user enters g, b, r and y then form colored to green, blue, red, and yellow respectively. Q3: Write a program to print multipliers of 5 (from 5 to 50)
20 R3 Which tools that can be used to :3 draw the following shape in .AutoCAD 37 23 43 R3 dimension, circle, arc, line, scale and rectangle 30 dimension, arc, line, rectangle, purge, and block construction line, polygon, arc, polyline, and dimension rectangle, trim, dimension, polyline, circle, and arc O O
The given picture shows the following parts of a blower. Please state its functions and discuss how a part works. Note: Do not copy and paste your answer. I need a non plagiarized answer for this one. A unique and thoughtful answer would suffice your answer. Use tables in answering this. Thank you!
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
TOPIC: Curvilinear Motion. Rectangular Coordinates REQUIRED: Determine the smallest and largest distance R at which the end of A of the car may be placed from the conveyor so that the packages enter the car. CAN YOU PLS DONT TYPE IT OUT THE ANSWER PLS WRITE IT OUT THE COMPLETE SOLUTION FOR BETTER UNDERSTANDING AND PLS ANALYZE WHAT IS REQUIRED. DONT COPY THE EXISITING SOLUTION ROUND OFF ANSWER TO FOUR DECIMAL PLACES
%3D Galcukle Ihe voiide re by an Icked gog going rom ARDiake A hoc for each b) ABG o AC direchlys ABE ->
Use the attached graph to answer the follwing questions a. Write an equation that gives the position with respect to time (use specific quantities) b. Write an equation that gives the velocity with respect to time (use specific quantities) c. Draw a velocity over time graph for this motion from t=0 to t=12s.
Pls solve
Below is problem MV1 from the course pack. In an earlier assignment, you created a multiview drawing of this part. Model this part with SolidWorks, with each grid spacing equal to one inch. Create a SolidWorks drawing of this part, with Front, Top, and Right Views. Import dimensions from the SolidWorks part file, and place them on the drawing so that they can be easily read. Add a note that all dimensions are inches. Add your personalized title block that you created in Chapter 2 to this drawing. *Important: Save the drawing first as SolidWorks Drawing (filetype *.slddrw) and then as an eDrawing (filetype *.edrw)! You will upload the eDrawing in Blackboard, not the SolidWorks Drawing - the SolidWorks drawing is associated with the part file, I cannot open the sw drawing unless you also send the part file; however, l can open the eDrawing without the part file.