A pump draws water from a 200mm diameter suction pipe and discharges through a 150mm pipe in which the discharge is 80 L/s. The pressure at point A is -40KPa. The 150mm pipe discharges into air at point B as shown. If the head loss from point A to point B is 5m, determine the power needed to be given by the pump in horsepower.

A pump draws water from a 200mm diameter suction pipe and discharges through a 150mm pipe in which the discharge is 80 L/s. The pressure at point A is -40KPa. The 150mm pipe discharges into air at point B as shown. If the head loss from point A to point B is 5m, determine the power needed to be given by the pump in horsepower.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem-2: It is required to deliver discharge Q = 0.04 m'/s against a total head Hp =VEN m using a pump has an impeller inner to outer diameter ratio of 0.5, speed of N= 20EN rpm and hydraulic efficiency of 0.90. If the flow at the entrance is radial such that Vn = V2, use the o and y equations to find the impeller rim v2 and flow velocities V2, exit width B2, and blades inlet B1 and outlet angles B2. %3D %3D %3D 0 = eNM +0.88 and y =eN +0.055 -5.25 -6.2 V, = Ø/28H, = TD,N/ 60 %3D V, = TD,N/60 EN=62 Vn =Vn=Q/4, =Q/ TB,D, H, = N,H, = N,v,V½/g B = tan -1 and B, = tan 2-V
During a flow of 450 L/s, a pressure of 65 kPa was measured at point C in 320 mm diameter horizontal the supply line of water turbine and a -47 kPa pressure T. was measured at point D, 2 m below point C at the 460 diameter exit pipe. mm Compute the total head extracted by a. the turbine. b. Compute the power supplied to the turbine in horsepower.
The nozzle which furnished the water to a certain hydraulic turbine 275mm in diameter and has coefficients of velocity and discharge of 0.98 and 0.96, respectively. The nozzle is supplied from a 60cm pipe in which the water approached the nozzle with a total head of 330m. Compute the following: a. Energy per second delivered by the jet to the turbine. b. Energy measured in hp lost in passing through the nozzle.
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
6) Turbulent water flows from a tank to a pipe. The head loss relationship in the pipe can be 25 (-)). What is the discharge of water? described as h₁=0.025 몰 Water T = 60°F Elevation 100 ft D = 1 ft ↓ ↑ L = 1000 ft Elevation 60 ft 6 in. diameter jet
A nozzle is fitted at the end of a pipe of length 100 m and of diameter 150 mm. For the maximum transmission of power through the nozzle, determine the diameter of nozzle. Take f = .009.
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
the 9.63. When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe, the head loss is 36 m (120 ft). Calculate the flowrate. 9.64. A pump of what power is required to pump 40 1/min of crude oil from a tank of surface elevation 12 to one of elevation 18 through 450 m of 75 mm pipe, if the oil is at (a) 25°C, (b) 40°C?
The 600 mm pipe shown conducts water from reservoir A to a pressure turbine, which discharges through another 600 mm o pipe into tail race B. The head lost from A to 1 is 5 times the velocity head in the pipe and the head lost from 2 to B is 0.2 times the velocity head in in the pipe. If the discharge is 700 L/s A) Compute for the total head lost 1. 05: Compute for the extracted energy cause by the turbine Compute for the hp given up by the turbine. V Answer A) EL 60m 600 mm 1.63 m 58.37 m 537.3 hp 600 mm o B ▷ EL 0 m
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m