Water enters a motor through a 400 mm diameter pipe under a pressure of 85 kPa. The exhaust pipe is 600 mm in diameter with a pressure of -8 kPa and is 3 meters below the 400 mm line. Compute the power supplied to the motor if 450 liters per second of water enters the motor and the total head loss is 4 m. Select one: O a. 25.4 Hp O b. 32.6 Hp O c 47.2 Hp O d. 53.3 Hp

Water enters a motor through a 400 mm diameter pipe under a pressure of 85 kPa. The exhaust pipe is 600 mm in diameter with a pressure of -8 kPa and is 3 meters below the 400 mm line. Compute the power supplied to the motor if 450 liters per second of water enters the motor and the total head loss is 4 m. Select one: O a. 25.4 Hp O b. 32.6 Hp O c 47.2 Hp O d. 53.3 Hp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the 11 cy diametersuction pipe leading to pump in the figure, the pressure at point A in the suction pipe is a vacuum of 12 cm of mercury, If the dischange SO02 mBVs of oil (SG H0.85), find the total energy head (m) at point A with respect into a datum at the pump Discharge pipe Suction pipe Darum Pump 1.200 m Oil (sp gr =0.85) Activate Windows o to seftings to activate Windows Express your answer in 2 decimal places 112 prt sc pause break f10
6. The nozzle which furnished the water to a certain hydraulic turbine 275 mm in diameter and has coefficient of velocity and discharge of 0.98 and 0.955 respectively. The nozzle is supplied from a 60 cm pipe in which the water approached the nozzle with a total head of 330 m. Compute the energy per second delivered by the jet to the turbine and the energy measure in horsepower lost in passing through the nozzle.
Q1/ liquid is pumped from a ground 90 elbow 90° For this system: - (Le/d) of globe valve = 240 (Le/d) of 90" elbow = 40 (Le/d) of 45" elbow - 18 h: of Heat Exchanger 1 = 2.2 m of liq. Fof Heat Exchanger 2 = 25 J/kg Pump efficiency elbow level reservoir to an overhead tank H.Ex.2 through a 15 cm ID pipes of e/d = 0.018 as shown in figure: i. What is the pressure developed by the pump to supply water to Tank Globe Valve 45" elbow - 62 % Pump the tank at the rate of 960 45° elbow /min? ii. What is the power required for the pump? Given that: u = 1.6 cP; sp.gr 0.86; and the lengths as follow; L = 33 m, L2 = 17 m, L3 = 8 m, L4 = 35 m Reservair H.Ex.1
Solution added
Q3
PLEASE ANSWER ASAP. WILL UPVOTE. PLEASE HELP
Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe. a. Draw the diagram. b. Solve the problem. Provide complete solution.
Fluid 1
The 600 mm pipe shown conducts water from reservoir A to a pressure turbine, which discharges through another 600 mm o pipe into tail race B. The head lost from A to 1 is 5 times the velocity head in the pipe and the head lost from 2 to B is 0.2 times the velocity head in in the pipe. If the discharge is 700 L/s A) Compute for the total head lost 1. 05: Compute for the extracted energy cause by the turbine Compute for the hp given up by the turbine. V Answer A) EL 60m 600 mm 1.63 m 58.37 m 537.3 hp 600 mm o B ▷ EL 0 m
The rate of flow of water through a pipe of length 2000 m and diameter 1 m is 2 m³/s. At the end of the pipe a nozzle of outside diameter 300 mm is fitted. Find the power transmitted through the nozzle if the head of water at inlet of the pipe is 200 m. Co-efficient of friction for pipe is 0.01.