Part C - Part CReplace the triangular distributed load by a single force F. At what e distance does this distributed load act, measured from O?Enter the distance from point O in units of m to three significant figures.nν ΑΣφIt vecmSubmitRequest AnswerPart D- Part DExpress the cable that runs from B to C as position vector rBCc in Cartesian vector form.Enter the components of the position vector separated by commas. Express your answer in units of m to three significant figures.vec?TBC,, TBC,, TBC, =mSubmitRequest Answer A post is supported by a ball-and-socket joint at O and cables BC and BD.A triangular distributed load runs from O to A as shown and has a maximum intensity of w = 36 N/mLength OA is 1.6 m and length OBis 2.5 mOther dimensions are given:h = 1.48 ml1 = 0.89 mha = 0.97 mlb = 0.65 mDC,hzh1l, 012AВyW

Part C An equivalent load for triangular distribution load can be determined from the formula as…

A post is supported by a ball-and-socket joint at O and cables BC and BD. A triangular distributed load runs from O to A as shown and has a maximum intensity of w = 36 N/m Length OA is 1.6 m and length OB is 2.5 m Other dimensions are given: h = 1.48 m l = 0.89 m ha = 0.97 m l2 = 0.65 m C h2 12 A B y W

A post is supported by a ball-and-socket joint at O and cables BC and BD. A triangular distributed load runs from O to A as shown and has a maximum intensity of w = 36 N/m Length OA is 1.6 m and length OB is 2.5 m Other dimensions are given: h = 1.48 m l = 0.89 m ha = 0.97 m l2 = 0.65 m C h2 12 A B y W

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: a) Using the numbering system of nodes and bars shown in Figure 1, state the 2 local stiffness…

Q: Consider the following diagram showing a rectangular steel bar supporting two overhanging loads: y…

A: Given Datab=6h=32 As given statement there is not given of question demand so we assume to…

Q: Two steel wires support a moveable overheadcamera weighing W = 28 lb (see fgure part a) usedfor…

A: W=28lb α = 22° β = 40°diameter1=30milsdiameter2=35mils1mil=0.001in To-Find:- a) Tensile stresses σ1…

Q: What is the maximum permitted tension in N in the cable if the vertical deflection at A has a design…

A: calculate the allowable twist: deflection at point A = 15 mm L1 = 200 mm twist = allowed delection/…

Q: Consider the frame below consisting of 3 beams with pins at B, C, and D. Beam CDE is 7 meters long,…

Q: investigate whether the safety requirement

Q: 0.4 m 0.2 m y 0.3 m 0.6 m HF .5 m EFG kirişinin enine kesiti B 0.25 m 1200 N Q2) As shown in the…

A: Given: The weight carried by structure, W = 1200 N The width of the cross-section, b = 25 mm The…

Q: Which of the folloving equations correctiy describe the bending moment M and torsion Tin section BC…

Q: Q1. Links BC and De are made of the same material (E = 29x106 psi) %3D and have the same cross…

A: The free-body diagram of the figure is given below: Taking moment about point F :…

Q: Q/Draw free body diagram then find reactions at pin support (O) and smooth surface (B) take beam OB…

Q: A beam is supported by a pin at point A and a cable that passes through a pulley at point D. There…

A: To find:a) The reaction force at EF and pin Ab)The internal forces at the midpoint of section AB and…

Q: Two steel pipes are used to support a 50KN load, as shown below. The pipes are connected to the wall…

A: Draw the FBD and find supports reactions

Q: Which of the following general equations can be used to find the vertical deflection of A in the y…

Q: Given a system composed of a bar fixed at the end on the left and subjected to various loads shown…

Q: 1.5 m 3 m 400 N 200 N 1 m Member AB is supported by a cable BC and at A by a square rod which fits…

A: Given data: F1=200 NF2=400 NuBC=-0.857i+0.429j+0.286k Need to determine the tension in the cable.

Q: rod. The pitch of the threads is p1.5 mm. Hanger Frame Parallel Knurled nut- springs Threaded rod D…

A: For solution refer below images.

Q: A bridge truss extends x = 206 m across a river (shown in the figure below) where 8 = 39°. The…

Q: A uniform stone slab weighs 400 lb and is suspended by 3 cables and subjected to a downward vertical…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Part C - Part C
Replace the triangular distributed load by a single force F. At what e distance does this distributed load act, measured from O?
Enter the distance from point O in units of m to three significant figures.
nν ΑΣφ
It vec
m
Submit
Request Answer
Part D- Part D
Express the cable that runs from B to C as position vector rBCc in Cartesian vector form.
Enter the components of the position vector separated by commas. Express your answer in units of m to three significant figures.
vec
?
TBC,, TBC,, TBC, =
m
Submit
Request Answer

A post is supported by a ball-and-socket joint at O and cables BC and BD.
A triangular distributed load runs from O to A as shown and has a maximum intensity of w = 36 N/m
Length OA is 1.6 m and length OBis 2.5 m
Other dimensions are given:
h = 1.48 m
l1 = 0.89 m
ha = 0.97 m
lb = 0.65 m
D
C,
hz
h1
l, 0
12
A
В
y
W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pins at B and D in the figure apply an axial load to diagonal bracing member BD. If BD has a rectangular cross-section measuring 0.50 in. X 2.00 in., what is the axial stress in member BD when the load is w0=220 lb/ft?
5 kip/ft ( parabolic (2nd order) 3 C В -10 ft -10 ft The structure above is supported by a rocker at A and a pin at B. The structure is subjected to a parabolic (i.e. second order) distributed load, as shown. Assume that the rocker at A can resist a compressive or tensile normal force. Which of the following is closest to the vertical force reaction at the pin (i.e. By)? a) 50 kip b) 0 c) 22.5 kip O d) 33.3 kip
A prismatic bar is supported between two rigid supports as shown in figure. The support reaction will be A B C 10 kN 1 m 2 m
The rigid rod shown below is free to rotate about O. Answer parts C and D Ans. To check: Rx=4.97lb Ry=17.5lb
Figure Q2 shows an 11 m long steel beam AC of uniform cross-section, simply supported at left end A and roller supported at location B. A uniformly distributed load of 40 kN/m is applied on the part AB of the beam together with a concentrated load of 20 kN at the end C. 20 kN 40 kN/m В. 8 m 3 m