A pipeline ABC 300 m long, is laid on an upward slope of 1 in 60. The length of the portion AB is 150 m and its diameter is 0.15 m. At B the pipe section suddenly enlarges to 0.30 m diameter and remains so for the remainder of its length BC, 150m. A flow of 50 L/s is flowing into the pipe at its lower end A and is discharged at the upper end C into a closed tank. The pressure at the supply end A is 140 kPa. Determine the maximum pressure at point C if f = 0.02 and the celerity is 2000 m/s.

A pipeline ABC 300 m long, is laid on an upward slope of 1 in 60. The length of the portion AB is 150 m and its diameter is 0.15 m. At B the pipe section suddenly enlarges to 0.30 m diameter and remains so for the remainder of its length BC, 150m. A flow of 50 L/s is flowing into the pipe at its lower end A and is discharged at the upper end C into a closed tank. The pressure at the supply end A is 140 kPa. Determine the maximum pressure at point C if f = 0.02 and the celerity is 2000 m/s.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m/s. 1 Pipe Length Diameter Friction Factor 1,800 mm 1,500 mm 2,000 mm 0.020 0.018 0.022 400 mm A 2 в у 350 mm 3 300 mm 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
A single pipeline x joins pipelines 1,2, and 3 at junction A, and merges again at junction B to form a single pipeline y. Pipelines 1,2, and 3 are parallel to each other. The pressure heads at A and B are 70 m. and 46 m., respectively. Assuming C = 120 for all pipelines, and Pipe 1 length = 3000 m. and diameter = 300 mm, Pipe 2 length = 1300 m. and diameter = 200 mm, and Pipe 3 length = 2600 m. and diameter = 250 mm. Compute the rate of flow at pipeline 1. a. 0.06 m^3/s b. 0.07 m^3/s c. 5.8 m^3/s d. 8.7 m^3/s
Kindly solve the problem and provide detailed solution for this.
The figure below shows a branched system in which the pressure at A is 700 kPaand the pressure at B is 550 kPa. Each branch is 60 mlong.Neglect losses at the junctions but consider all elbowsin both branches. If the system carries oil with a specific weight of 8.80 kN/m3, calculate the total volume flow rate.The friction factor of the DN 100branch (call thisBranch a) is 0.02and the friction factor of the DN 80branch (call this Branch b) is 0.022. Assume all elbows are standard.(Answer: 6.07×10−2?3/?)
Three pipes, pipe 1, pipe 2 and pipe 3, are connected in series. Pipe 1 has diameter of 600mm and length of 850m. Pipe 2 has diameter of 450mm and length of 903m. Pipe 3 has diameter of 350mm and a length of 510m. Determine the total head loss from start of pipe 1 to end of pipe 3 if the discharge in pipe 1 is 345 L/s. f = 0.021 in all pipes A) HL= 38.86 m B hf = 41.17 m с HL = 29.52 m (D HL = 32.41 m E HL = 36.69 m F No answer among the choices
Asap!!!
If the total flow of 4.0m3/? takes place in the three pipes. Determine the distribution offlow. The pipe lengths, diameters and frictions factors are shown below.
1.) SAE 10 oil at 20° (ρ=869 kg/m³, μ=8.14 × 10-2 N•s/m²) flows in a 200 mm diameter pipe. Find the maximum velocity for which the flow will be laminar.
The average velocity of the steady flow at A and B is indicated. Determine the average velocity at C.The pipes have cross-sectional areas of Aa=Ac=0.1mm^2 and Ab=0.2m^2
For the branching pipe system shown, determine the flow in each branch. The fluid in each reservoir is water at 20°C and all pipes are made of cast iron
At two points 1 and 2 in a pipeline the velocities are V and 2V, respectively. Both the points are at the same elevation. The fluid density is p. The flow can be assumed to be incompressible, inviscid, steady and irrotational. The difference in pressure P1 and P₂ at points 1 and 2 is 2
Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m³/s. Pipe Length Diameter Friction Factor 400 mm 1,800 mm 1,500 mm 2,000 mm 1 0.020 X A 2 в У 2 350 mm 0.018 300 mm 0.022 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s