A A 2 B The three-reservoir system is shown below: 3 |C The elevation of Reservoir at A is 140m and at C is 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f- 0.02, and sizes namely: Pipe Diameter 1 (mm) - 600mm Pipe Diameter 2 (mm) - 500mm Pipe Diameter 3 (mm) - 400mm Determine the Headloss at Pipe 3 in meters.

A A 2 B The three-reservoir system is shown below: 3 |C The elevation of Reservoir at A is 140m and at C is 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f- 0.02, and sizes namely: Pipe Diameter 1 (mm) - 600mm Pipe Diameter 2 (mm) - 500mm Pipe Diameter 3 (mm) - 400mm Determine the Headloss at Pipe 3 in meters.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the piping system shown below, determine the flow distribution and the piezometric heads at the junction (j) using the Newton-Raphson Method of solution, power 20 Kw D = 0.2 m, D,= 0.15 m, D,= 0.15 m f= 0.021, f,= 0.018, f, = 0.023 L1=100 L2=145 L3=350 30 m В 2 15 m 10 m A Pump 1 j
Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).
Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm o pipe, 600m long. Using f = 0.02 and the hydraulic grade line shown, determine the following: a) power supplied by the pump, b) power loss by the turbine, and elevation maintained by reservoir B. El. 200 hfj El. 190 НЕ El. 180 hf, B El.100 A P TURBINE PUMP ANSWER: a. Power = 1557.828 kW, b. Power = 155.7828 kW c. Elevation of B = 170 m %3D
Situation 7: From reservoir A whose water surface elevation is 225 m. Water is pumped through a 350 mm pipe across a valley at a second reservoir B at a elevation of 240 m. During pump, the pressure is 570 kPa at a point C and at elevation of 195 m. Assume that the headloss in the pipe from reservoir A to point C is 30 times its velocity head and from point C to reservoir B is 50 times its velocity head 23. Compute the discharge in the pipeline in L/s 24. Compute the head added by the pump 25. Compute the horsepower exerted by the pump IVA E1225 m El 240 m El 195 m
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. Include minor losses. (DO NOT ROUND OFF)
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
For the pipe networks shown, the flow of water from reservoir A to the junction is 0.035 cu.m.per second. a) Determine Q2, Q3 b) Determine the head loss from A to B
An engineer is hired to design a swimming pool 15 m long by 6 m wide by 2 m deep. For water supply, he decides to lay 600 m of 5 cm pipe with f = 0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550 kPa and the difference in elevation between the two ends of the pipe is 10 m, with the discharge end higher than the intake end. Assuming that 10 % of the loss in the pipeline are due to transitions, fittings, and valves, how long will it take to fill the swimming pool?
A pipe has a length of 213 m., and a diameter of 0.46 m. The coefficient of rouaness is C = 171, and the headloss is 17 m. Determine the discharge (L/s) inside the pipe.
2. Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Pipe 1: L = 5000 m, D = 300 mm Pipe 2: L = 4000 m, D = 250 mm Pipe 3: L = 3500 m %3D The flow from reservoir A to junction P is 0.045 m3/s and f for all pipes is 0.018. (a) Find the elevation of the energy grade line at P in m (b) Determine the flow on pipe 2 in m3/s (c) Compute the diameter appropriate for pipe 3 in mm
Three reservoir, named A,B, and C are connected by Pipe 1, Pipe 2, and Pipe 3 respectively joining at a common junction. Determine the into or out of the reservoir A in the pipe system, given the following data. Use n=0.011 for all pipes. Reservoir A at El. 30 m, B at El. 24 m, and C at El. 15 m Pipe 1: 30 cm dia. 1200 m long Pipe 2: 20 cm dia. 900 m long Pipe 3: 16 cm dia. 1500 m long
Question 3) Water transmission line is constructed to transmit water from A reservoir to city with 200 l/s of total discharge. 150 l's is supplied from reservoir and the other part is added from B point (Use same types of pipes through the pipeline). Maximum allowable pressure on the pipeline is 100 m. Minimum pressure of transmission line, (–), = 3 m, William-Hazen coefficient, C is 100. (V = 0.85CR0 Josa ). Determine the diameter of pipeline, design WTL economically. Commercial Pipe Diameters: $200,250, 300,350, 400, 450, 500, 550, 600. 250m 162m (A) (3) 100m 50 V's/ (B) 1000 m 2000 m City 3000 m