Three pipes, pipe 1, pipe 2 and pipe 3, are connected in series. Pipe 1 has diameter of 600mm and length of 850m. Pipe 2 has diameter of 450mm and length of 903m. Pipe 3 has diameter of 350mm and a length of 510m. Determine the total head loss from start of pipe 1 to end of pipe 3 if the discharge in pipe 1 is 345 L/s. f = 0.021 in all pipes

Three pipes, pipe 1, pipe 2 and pipe 3, are connected in series. Pipe 1 has diameter of 600mm and length of 850m. Pipe 2 has diameter of 450mm and length of 903m. Pipe 3 has diameter of 350mm and a length of 510m. Determine the total head loss from start of pipe 1 to end of pipe 3 if the discharge in pipe 1 is 345 L/s. f = 0.021 in all pipes

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Kindly answer 1,2 and 3 please
2. Given H = 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses through the tank outlet if the exit discharge were 0.163 m³/sec. H D
I need the answer as soon as possible
Please answer it soon
please consider minor and major losses
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
Three pipes 1, 2, 3 are connected in parallel. The properties of each pipe are given in the table. The combined discharge of the three pipes is 0.61 m3/s. Use Hazen-Williams coefficient of 100 for all pipes. Use table below for the properties of the pipes. a.) calculate the total head loss (A. 181 m B. 461 m. C . 411 m. D. 731 m) b) Solve for the rate of flow in pipe 1 ( A. 0.1249 m3/s. B. 0.1645 m3/s. C. 0.1145 m3/s. D. 0.1225 m3/s). C.) c) Calculate the rate of flow in pipe 2. ( A. 0.1032 m3 /s. ,B. 0.1255 m3 /s. C. 0.7865 m3/s. D. 0.3955 m3/s)
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az
Three pipes, pipe 1, pipe 2 and pipe 3, are connected in series. Pipe 1 has diameter of 600mm and length of 850m. Pipe 2 has diameter of 45omm and length of 903m. Pipe 3 has diameter of 350mm and a length of 510m. Determine the total head loss from start of pipe 1 to end of pipe 3 if the discharge in pipe 1 is 345 L/s. f = 0.021 in all pipes A) HL = 32.41 m (B hf = 41.17 m No answer among the choices D) HL = 29.52 m E HL = 36.69 m F) HL = 38.86 m
Question 1: For the setup shown in the figure: H = 20 m f = 0.0012 f = 0.0012 D = 250 mm D = 80 mm L = 50 m L = 50 m f = 0.001 D₁ = 150 mm L = 100 m A. Calculate Q in the 150 mm-diameter pipe B. If the NPSHR of the pump is 3 m. Is it feasible to use the pump? You can use: Patm-101 kN/m², and Pvapor = 3.17 kN/m² H₂ = 10 m Pump Q f = 0.0012 D=80 mm L = 50 m Q₁ = 0.2
A pump draws 24L/s of water from reservoir A and lifts it to reservoir B. The head lost from A to 1 is 3 times the velocity head in the 150mm suction line and the head lost from 2 to B is 25 times the velocity head in the 100mm discharge line. (A) What is the power delivered by the pump to the system in hp? (B) What is the pressure head in meters in point 1? (C) What is the pressure head in meters in point 2?
Two pipes 1 and 2 are connected in parallel. Pipes 1 and 2 have the same length and diameter. If the flow in pipe 1 is 680 L/s and the friction factor in pipe 2 is twice of the friction factor of pipe 1, determine the discharge of pipe 2. A) 530 L/s B 460 L/s c) 481 L/s No Answer among the choices E) 509 L/s