A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C). The first output gear (B) takes (15 kw) and the remaining power delivered to the second gear at (A) . If the modules of elasticity E-200 Gpa and 0.3 poison ratio. Calculate the shearing stress at each section and the total angle of rotation between C and A. Knowing that the shaft rotates at 6 Hz. 55 mm 65 mm Fig 3 4m 2 m -

A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C). The first output gear (B) takes (15 kw) and the remaining power delivered to the second gear at (A) . If the modules of elasticity E-200 Gpa and 0.3 poison ratio. Calculate the shearing stress at each section and the total angle of rotation between C and A. Knowing that the shaft rotates at 6 Hz. 55 mm 65 mm Fig 3 4m 2 m -

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The nature of the stresses

A: Given; A helical gear with pressure angle,α= 200 and β=300 helix angleAt the mid span of a shaft is…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: According to the given dataWe need to findminimum required diameter for the segments 1 and 2

Q: A hollow steel tube has an outside diameter of 224 mm and inside of 201 mm. Which of the following…

Q: d-150 mm d,-300 mm 4,4 kN 4 B 150 mm KSAN 300 mm 300 mm

A: When an external force is applied to an object and when that force tends to bend the object is…

Q: 2. In the gear system shown, the motor applies a torque of 600 N-m to the gear A. Shafts (1) and (2)…

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: In a broaching machine shown, shaft A carries a pulley 60.96 cm in diameter which is driven by a…

A: Given Data:Based on the given problem, the solution is as follows:Convert the motor power from…

Q: Problem 5-57: The turbine develops 150 kW of power, which is transmitted to the gears such that C…

A: Given data as per the questionpower developed =150 kwdiameter of shaft =100 mm =0.1 mRotational…

Q: A compound steel [G = 80 GPa] shaft consists of a solid 86-mm-diameter segment (1) and a solid…

Q: An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached…

Q: he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if…

A: ⇒given data;⇒shear modulus(G)=75GPa =75*103MPa⇒angle of twist for gear…

Q: the centre distance in mm

A: Given data; Compound gear train with gears; p=20 teeth Q= 40 teeth R= 15 teeth S=20 TeethGears…

Q: Two motors deliver 119 hp each at 1000 rpm to shafts at A and D. The shaft transmits torque through…

A: Data given- Motor deliver = 119 hp N = 1000 rpm Shear modulus = 11 × 103 ksi

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: 3. Gear B supplies 20 KW of power, while gears A, C and D withdraw 6 kW, 4 kW and 10 kW,…

Q: A solid circular shaft of 35 mm diameter transmits a torque of 1460 Nm. The value of maximum shear…

A: Diameter of solid circular shaft, d = 35mm Torque transmitted, T = 1460 Nm or 1460000 Nmm

Q: 03: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

A: The given question belongs to the topic Torsion of circular shafts. In this question, rotation given…

Q: Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

A: Given data: Power at Gear C, PC= 40kW Power at Gear B, PB=15KW Power at Gear A, PA= 40-15=25kW…

Q: odule of .05 inch, which rotates at 4000 rpm and has a pitch-line velocity of 15 ft/s. the second of…

Q: Determine the torque in ft-Ib that can be applied to a 1-in diameter circular shaft if the shearing…

A: According to the given data τ=8000 Psi D=1 in We need to find The torque in ft-Ib that can be…

Q: the diameter of solld snaft (2) IS E. 72 teeth 30 teeth (1) (2)

A: Givenspeed of motor NA=808rpmZA=24ZB=72ZC=30ZD=60

Q: Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below.…

A: Consider the given figure. For the shaft AB, in equilibrium condition the torque acting on the gear…

Q: The small gear of an internal gear train shown in the figure is powered by a 500-kW motor at 30 Hz.…

A: Given data:

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

Q: pplied torque of 1.5 Nm is found to produce an angular twist of 0.4°, measured on a length of 0.2 m…

A: Given data,hollow shaftD=50mm=0.05m so, R=0.025d=30mm=0.03mTa=1.5 Nmθ=0.4°⇒0.4×π180=0.006981…

Q: A hollow steel tube has an outside diameter of 227 mm and inside of 208 mm. Which of the following…

Q: angle angle and 3 1 ween two bearin

Q: Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an…

A: Given data, Power=150hp speed=250 rpm shear stress=4.7ksi angle of twist =0.35°…

Q: 3. A gear transmits 20 kW at a pitch line velocity of 6000 ft/min. If the cut gear service is…

Q: PROBLEM NO. 1 A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20…

A: Given data: D=40 mmL=533 mmd1=20 mmd2=30 mmτ=80 MPaN=230 rpm Need to determine the maximum power…

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located
at (C). The first output gear (B) takes (15 kw) and the remaining power delivered to the
second gear at (A) . If the modules of elasticity E-200 Gpa and 0.3 poison ratio . Calculate the
shearing stress at each section and the total angle of rotation between C and A. Knowing that
the shaft rotates at 6 Hz.
55 mm
65 mm
Fig 3
4 m
2 m
U

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to operating machinery in the factory, and the remaining power in the shaft is transferred by gear D. Shafts (1) and (2) are solid aluminum [G = 4400 ksi] shafts that have the same diameter and an allowable shear stress of T = 5.8 ksi. Shaft (3) is a solid steel [G=9100 ksi] shaft with an allowable shear stress of T = 10.2 ksi. Assume that L₁=2.3 ft, L₂=1.2 ft, L3-2.9 ft. Determine: (a) the minimum permissible diameter d₁=d₂ for aluminum shafts (1) and (2). (b) the minimum permissible diameter d3 for steel shaft (3). (c) the rotation angle D/A of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b). Answers: (a) d₁=d₂ = i (b) d3= i (c) & DIA = i (1) L₁ TB. B (2) L2 in. in. o' (3) L3 Tp Mommu D
please help solve
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
Solve the following problems and SHOW YOUR COMPLETE SOLUTIONS FOR BETTER UNDERSTANDING
Please answer in proper units
Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten solution is more preferred than typed. A 40-mm diameter, 522-mm length shaft is drilled, for a part of its length L1, to a 20 mm diameter and for the remaining length L2 to a 30 mm diameter drill hole. If the allowable shear stress is 86 MPa, find the maximum power that the shaft can transmit at a speed of 226 rev/min. If the angle of twist in the length of 20 mm diameter drill hole is equal to that in the 30 mm diameter drill hole, find the length of the shaft that has been drilled to 20 mm and 30 mm diameter.
The motor on the left provides a torque of 5500 N•m to the gear shaft shown. The motor runs machines connected to gears B, C and D requiring torques of 3000 N•m, 1500 N•m and 1000 N•m respectively. A, B, C and D are spaced 2000 mm apart and the diameter of the shaft is 75 mm. The shear modulus of the shaft material is 80x109 N/m2. Determine: Minimum diameter required (in millimeters) if the shearing stress in the shaft is limited to 100x106 N/m2 Rotation of D with respect to A Note: Draw the Free Body Diagram, Compute for all of the necessary elements, Include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
A spur gear with 20° full depth teeth is transmitting 20 kW at 200 rad/s. The pitch circle diameter of the gear is 100 mm. The magnitude of the force applied on the gear in the radial direction is
Please hel me solve this asap. Thank you!!
A pair of gears, having 40 and 30 teeth respectively are of 25° involute form. The addendum length is 5 mm and the module pitch is 2.5 mm. If the smaller wheel is the driver and rotates at 1500 r.p.m., find the velocity of sliding at the point of engagement and at the point of disengagement
Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D