A part made from AISI 1212 steel undergoes a 20 percent cold-work operation. (a) Obtain the yield strength and ultimate strength before and after the cold-work operation. Determine the percent increase in each strength. (b) Determine the ratios of ultimate strength to yield strength before and after the cold work operation. What does the result indicate about the change of ductility of the part?

A part made from AISI 1212 steel undergoes a 20 percent cold-work operation. (a) Obtain the yield strength and ultimate strength before and after the cold-work operation. Determine the percent increase in each strength. (b) Determine the ratios of ultimate strength to yield strength before and after the cold work operation. What does the result indicate about the change of ductility of the part?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Distinguish between the Normal and Shear Stress Components?
Problem 2: A catastrophic failure occurred to a 7079-T6 aluminum alloy shaft. The maximum tensile stress was specified as 30% of the yield stress (0₂ = 300 MPa) and the stress ratio R was zero. Post-failure examination found that fatigue crack growth striation started at a depth of 2.0 cm from the surface, and the striation spacing was 1.3 x 10-4 cm. The fatigue-crack growth behavior of the aluminum alloy is given in the right figure. The manufacturer claimed that the part was overloaded by the user, but the user denied the allegation and sued the manufacturer. As a mechanical engineer, what is your verdict based on your calculation? da/dN (μm)/cycle 4 6 8 10 2.5TTTTT 1.0 0.25 Titanium Aluminum 0.05- 10 20 30 ksi Vin 40 60 80 100 • 200 Som 200 T -Steel 80 AK (MN/m2) 400 600 1000 • A533 alloy steel Ni-Mo-V alloy steel A HP 9-4-25 alloy steel 7079-T6 aluminum alloy 5456-H321 aluminum alloy Ti-6 Al-4V titanium alloy L 180 T 600 100 480 460 40 uin./cycle
Q.3. A cylindrical specimen of cold-worked Brass has a tensile strength of 500 MPa. If the specimen remained cylindrical during deformation and its original radius was 10.6 mm, determine its radius after deformation. The dependence of tensile strength on percent cold work is shown in the following Figure. 140 900 1040 Steel 120 800 700 100 600 Brass -80 500 -60 400 Copper 300 -40 200 10 20 30 40 50 60 70 Percent cold work Tensile strength (MPa)
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints.
I've got 38.35 and 34.3 please help me verify
A 20 foot long x 4 feet wide x ½ inch thick sheet of an aluminum alloy is cold rolled to a thickness of ¼ inch. During the rolling operation the with of the sheet increases by 10%. The strength coefficient (K) and the strain hardening coefficient (n ) for the aluminum alloy are 25,500 psi and 0.3, respectively. Calculate the length of the sheet after the rolling operation in feet.
If you could produce AISI 1020 steel with a grain size of 50 nm, what would be the expectedyield stress, assuming a Hall--Petch response? (  MPa, k=0.56 MN/m3/2). Explain eachterm in H-P relation.
4
Assume a matensetic steel (Kic = 110MPavm) whose fatigue crack growth rate is given on the attached sheet. A large steel plate with a central crack of length 2.5mm was designed to withstand an instantaneous remote tensile over-load of twice the maximum load. If the plate is subjected to a cyclic loading of 0 = = 158 [1 + coswt] MPa How many cycles can the piece safely withstand?
One metal sample is hot worked 40%; a second sample is hot worked 50%; a third sample is cold worked 40%; a fourth sample is cold worked 50%. Select all of the following that are true. Group of answer choices The 50% cold worked sample would have the highest yield strength. The two hot worked samples would have the highest yield strength and the hot worked yields are equal. The yield strength of all the samples would be about the same. The 40% hot worked sample would have the highest yield strength. The two cold worked samples would have the highest yield strength and the cold worked yields are equal. The 50% hot worked sample would have the highest yield strength. The 40% cold worked sample would have the highest yield strength.
1. Please draw a typical tensile test curve for low carbon steels and mark the four stages and list their names (use critical points on the curve to help you identify the start and end points of the four stages). 2. Show the yield, ultimate tensile strength and fracture points, as well as yield and ultimate tensile strength on the curve. 3. Please draw the load and unload curve for a stress level causing the low carbon steels to experience elastic deformation only. 4. Please draw the load and unload curve for a stress level causing the low carbon steel to experience permerment deformation, and identify both elastic and plastic strain on the drawing after unloading.
Need correctly