A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth

A pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of cast iron bevel gears connects the two shafts at right angles. The pitch diameters of the pinion and gear are 80 mm and 100 mm. The shape of the gear teeth is 14½0 composite form. The allowable static stress for both gears is 55 MPa. If the pinion transmits 2.95 kW of power at 1200 rpm, determine the module and the number of teeth in each gear from the power point of view and check the design from the wear point of view. Take the surface resistance limit is 630 MPa and the modulus of elasticity for cast iron is 84 kN/mm2.
please help
Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and transmits a torque of 20 N-m. The torque transmitted by the gear is
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear's teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1.1. If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1.2. Calculate the gear maximum velocity of sliding.
Three 14.5° pressure angle spur gears with a diametral pitch of 8 are meshed. The input pinion on the left is running clockwise at 3101 rpm and transmits 3.2 Hp. Gear 1 (Pinion) Input N1 = 20 teeth Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth Answer the following: 1. Pinion (Gear 1) pitch diameter 2. Gear 2 pitch diameter 3. Gear 3 pitch diameter 4. Circular pitch 5. Addenda 6. Center distance from gear 1 to gear 3 7. Line of action 8. Contact ratio of gear 1 and 2 9. Gear ratio from gear 1 to gear 3( for gear 1 contacting gear 2, 10. Draw a free-body diagram of Gear 2, showing the radial and tangential forces. Calculate these forces. What is the reaction force in the bearing?
What is the total force exerted by the pinion on the gear? Report your answer in lbf.
The four helical gears shown in figure have a module in the normal plane of 4 mm and a pressure angle in the normal plane of 0.35 rad. The motor shaft rotates 550 rpm and transmits 20 kW. Other data are on the drawing. (a) What is the speed ratio between the motor (input) and output shafts? (b) Determine all force components that the 20-tooth pinion applies to the 50-tooth gear. Make a sketch showing these forces applied to the gear. (c) The same as part (b), except for the force components that the 50-tooth gear exerts on the 25- tooth pinion 100 50 teeth 200 125 25 teeth ψ = 0.35 rad right hand Motor 20 teeth ψ = 0.50 rad left hand 50 teeth Output
What is the transmitted load exerted by the pinion on the gear? Report your answer in lbf.
1. Calculate the power that can be transmitted safely by a pair of spur gears with the data given below. Calculate also the bending stresses induced in the two wheels when the pair transmits this power. Number of teeth in the pinion = 20 Number of teeth in the gear = 80 Module = 4 mm Width of teeth = 60 mm Tooth profile = 20° involute Allowable bending strength of the material = 200 MPa, for pinion = 160 MPa, for gear = 400 r.p.m. Speed of the pinion Service factor = 0.8 0.912 0.154- T Lewis form factor %3D 3 Velocity factor 3 + v
please help
Three 14.5° pressure angle spur gears with a diametral pitch of 8 are meshed. The input pinion on the left is running clockwise at 3101 rpm and transmits 3.2 Hp. Gear 1 (Pinion) Input N1 = 20 teeth Gear 2 Idler Gear 3 Output N3 = 25 teeth N2 = 75 teeth Answer the following: 1. Pinion (Gear 1) pitch diameter (1 mark) 2. Gear 2 pitch diameter (1 mark) 3. Gear 3 pitch diameter (1 mark) 4. Circular pitch (1 mark) 5. Addenda (1 mark) 6. Center distance from gear 1 to gear 3 (2 marks) 7. Line of action length for gear 1 contacting gear 2 (2 marks) 8. Contact ratio of gear 1 and 2 (2 marks) 9. Gear ratio from gear 1 to gear 3 (1 mark) 10. Draw a free-body diagram of Gear 2, showing the radial and tangential forces. Calculate these forces. What is the reaction force in the bearing? (3 marks)
please help