The four helical gears shown in figure have a module in the normal plane of 4 mm and a pressure angle in the normal plane of 0.35 rad. The motor shaft rotates 550 rpm and transmits 20 kW. Other data are on the drawing. (a) What is the speed ratio between the motor (input) and output shafts? (b) Determine all force components that the 20-tooth pinion applies to the 50-tooth gear. Make a sketch showing these forces applied to the gear. (c) The same as part (b), except for the force components that the 50-tooth gear exerts on the 25- tooth pinion 100 50 teeth 200 125 25 teeth ψ = 0.35 rad right hand Motor 20 teeth ψ = 0.50 rad left hand 50 teeth Outpu

The four helical gears shown in figure have a module in the normal plane of 4 mm and a pressure angle in the normal plane of 0.35 rad. The motor shaft rotates 550 rpm and transmits 20 kW. Other data are on the drawing. (a) What is the speed ratio between the motor (input) and output shafts? (b) Determine all force components that the 20-tooth pinion applies to the 50-tooth gear. Make a sketch showing these forces applied to the gear. (c) The same as part (b), except for the force components that the 50-tooth gear exerts on the 25- tooth pinion 100 50 teeth 200 125 25 teeth ψ = 0.35 rad right hand Motor 20 teeth ψ = 0.50 rad left hand 50 teeth Outpu

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

can you please give me the solution for 1.27, thanks
Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth
a) Pressure on the quay Weight of the container: Length of the reachstacker. Length of the arm 32 tons 4 meters 14 meters. Pls calculate the pressure on the quay. What is the 32 pressure on tons the quay Discover your What is the axle pressure on the front axle (which is standing on the quay)? ??d>www.nhtv1 Quay b) The volume of a 45° container is 86.65 m3. The internal measures are: - Length: - Width: 44'5" ft 8'5" ft What is the height of the container? c) You received 180*20ft containers and the standard ratio of 40ft containers. How much TEU did you receive?
In (Eigure 1). Fy-700 N and @-20 Figure 30 FA-700 N 1 of 1 Determine the magnitude of the resultant force Express your answer to three significant figures and include the appropriate units. > View Available Hint(s) Fu Submit Part B. Value Determine the direction of the resultant force, measured counterclockwise from the p bitive y axis Express your answer in degrees using three significant figures. View Available Hint(s) Submit Units 15. ΑΣΦ. 11 Ivec Provide Feedback
Asiacell 念.l1 .all ZAIN IQ O STATI... -> FIND moments around O, A and B 500N 900N 60° 4m A 5m
F-90016 F₂=600% F₁=96016 30° ·x Part A Determine the magnitude of the resultant force acting on the corbel. Express your answer in pounds to three significant figures. ▸ View Available Hint(s) 15| ΑΣΦ 41 Ivec FR = Submit Part B 0= Determine the direction of the resultant force acting on the corbel measured counterclockwise from the axis. Express your answer in degrees to three significant figures. ► View Available Hint(s) IVE| ΑΣΦ | | vec ? ? lb 0
LAL 12 The density of a solid is its mass divided by its volume. If the less is measured as 42.5 ± 0.5 g and the volume as 54 ± 1 cm³, what it be the worst possible error in the calculated density?
. What force would be exerted against a seawall if a 1:36 model 0.914 m long experienced a wave force of 120 N?4. A surface vessel 156
2.34 Determine the resultant of the three forces of Prob. 2.22. Answer T
HW5 Q
is this drawing metric or inch?
For Further Research (Individual) For each of the typesof mechanical observation listed within the chapter(people meters, portable people meters, eye trackingtechnology), condua research online to identify (anddocument) the benefits and limitations of using eachmethod.