Answered: A pair of 105-N forces is applied to… | bartleby

Related questions

Question

A pair of 105-N forces is applied to the handles of the small eyelet squeezer. The block at A slides with negligible friction in a slot machined in the lower part of the tool. Neglect the small force of the light return spring AE and determine the compressive force P applied to the eyelet.

A pair of 105-N forces is applied to the handles of the small eyelet squeezer. The block at A slides with
negligible friction in a slot machined in the lower part of the tool. Neglect the small force of the light
return spring AE and determine the compressive force P applied to the eyelet.
105 N
66.5 mm
56 mm
C
B
18 mm
A
WWWWE
D.
7.50 mm
105 N
Answer: P =
N
the tolerance is +/-2%

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Answer must be according the correct signifcant numbers.
A one-string Aeolian harp is constructed by attaching the lower end of a 1.66-m-long rigid and uniform pole with a mass of 8.00 kg to a tree at a pivot and then using a light rope to hang a 39.0-cm-long hollow steel tube with a mass of 4.00 kg from its upper end. A horizontal wire between the pole and the tree is attached to the pole at a height h above the pivot and holds the pole at a 45.0∘C angle with the vertical. The wire is uniform and has linear mass density μ=1.40 g/m. When the wind blows, the wire resonates at its fundamental frequency. The height h is chosen such that the sound emitted by the wire stimulates the fundamental standing wave in the tube, which harmonizes with the resonating wire. The speed of sound in air is 344 m/s. What is the frequency of the note produced by this instrument?
Show complete solution
A system requires a metal component with the design specification that it not experience more than 0.1% linearized strain. During operation, the component experiences uniaxial extensional stresses ranging from 0 to 1000 kPa. Assuming isothermal LEHI behavior, what is the minimum Young's modulus that the metal must possess to be used to make the part?
The left-hand end of a 2.50 kg rod with a 2.00 m length is attached to a vertical wall by a hinge. A 3.00 kg object is suspended from the rod at a point 1.80 m from the hinge. The rod is held in a horizontal position by a light wire that runs from the right-hand end of the rod to the wall. The wire makes a 35.0degree angle with the rod. (a) What is the tension on the wire? (b) What is the vertical force on the hinge?
The Tethered Satellite in shown has a mass of 525 kg and is at the end of a 20.0 km long, 2.50 mm diameter cable with the tensile strength of steel. (a) How much does the cable stretch if a 100 N force is exerted to pull the satellite in? (Assume the satellite and shuttle are at the same altitudeabove the Earth.) (b) What is the effective force constant of the cable? (c) How much energy is stored in it when stretched by the 100 N force?
Rearange to find g T^2=4pi^2(1/g)
.
During a dunk, a basketball player will elevate theircenter of mass 70 cm (or more) while jumping off of one leg. What is the strain energy contribution to the energy required to elevate the center of mass given the following parameters? How much energy has to be contributed by active muscle contraction? mass = 82 kg, K leg = 35000N/m, dispacement = 0.11 m.
A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 1-in. gap between the two plates filled with glycerin as shown in Fig. (1). (1) Determine the torque required to rotate the circular plate slowly at 2 rpm. Assume that the velocity distribution in the gap is non-linear and that the shear stress on the edge of the rotating plate is negligible. Given: the dynamic viscosity of glycerin is 0.0313 lb.s/ft. (2) Find the shear force required to rotate the circular plate with the same velocity (2 rpm). (3) If the glycerin is replaced by air what are the values of torque and shear force. (4) What are the values of torque and shear force if we assume that the velocity distribution in the gap is linear. Rotating plate Torque 1 in. gap Fig. (1)
Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz.
What is the vertical force, Fy, exerted on the boom by the hinge?