A one-way slab having a simple span of 3 m is 160 mm thick. The slab is reinforced with 12 mm tension bars (fy=275 MPa) spaced at 140 mm o.c. Steel covering is 20 mm. Calculate the uniform live load pressure that a slab can carry. Use f'c = 20.7 MPa. Unit weight of concrete is 23.5 kN/m³.

A one-way slab having a simple span of 3 m is 160 mm thick. The slab is reinforced with 12 mm tension bars (fy=275 MPa) spaced at 140 mm o.c. Steel covering is 20 mm. Calculate the uniform live load pressure that a slab can carry. Use f'c = 20.7 MPa. Unit weight of concrete is 23.5 kN/m³.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the required tension steel area of the T beam with given properties below. Width of…

A: Given:- Width of flange, bf=500 mmWidth of web, bw=340 mmThickness of flange, tf=140 mmEffective…

Q: The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads…

A: In the question calculation of load on the beam is permissible until and unless there will no…

Q: PLEASE WRITE THE COMPLETE SOLUTION NEATLY: A rectangular beam has b = 250 mm and an effective depth…

A: b = 250 mm d = 490 mm fc' = 20.7 MPa fy = 420 MPa As = 3-20mm diameter bar Calculate ultimate…

Q: Determine the required tension steel area of the T beam with given properties below. Width of flange…

A: Given:- Width of flange, bf=500 mmWidth of web, bw=340 mmThickness of flange, tf=140 mmEffective…

Q: Given the following properties of a rectangular concrete beam: b = 300mm, d = 425mm, f'c = 28 MPa,…

Q: Please answer with complete illustration. A cantilever slab has a span of 2.40 m. It is 150 mm thick…

A: Loads are external forces that can produce stress, deformation, displacement, and acceleration in a…

Q: 1. Cracking moment of the section. 2. Compressive stress on the concrete. 3. Tensile stress on the…

A: The basis of this method is that the permissible stress for concrete and steel will not be exceed…

Q: 3 Given a concrete beam (width b= 10 in., depth h=25 in.) with flexural reinforcement at the bottom,…

A: Cracking: When the stresses or the forces which are imposed on the structure cannot be resisted by…

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy =…

A: Given data f'c = 26.27mpa fy = 414 mpa The As value was not given. so lets assume as 3bars of 32mm…

Q: mm- the Beam must carry a Service Calculate the Flexural Stress in the concrete using…

A: GIVEM m= 8 and area od concrete =total area - area of steel

Q: Problem 2: If f = 3 ksi what is the modulus of elasticity Ec and the maximum tensile stress fr that…

A: f'c = 3 ksi or 3000 psi We need to calculate modulus of elasticity Ec and tensile stress fr

Q: A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive…

A: From the given problem, Positive Bending moment = 78kip f'c = 3200psi span =26ft

Q: A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Situation #1: A reinforced concrete beam has a width of 300 mm and effective depth of 460 mm. The…

Q: Consider the following data: 1. 3-10 mm 0 bars are in bundle and are in compression. 2. Steel used…

A: Given data,

Q: Using the stress block, determine the ultimate moment of resistance of the section shown in Figure 2…

Q: Problem 1: Transformed Moment of Inertia and Elastic Deflection Given: The center of the top and…

A: If any structure consists of more than one shape and is made up of more than one material then it is…

Q: Three high-strength concrete poles, with an effective cross- sectional area of 40, 000m * m ^ 2 and…

Q: • A rectangular beam has the dimensions b=250mm, h=650mm, and d=600mm and is reinforced with three…

Q: Arectangular concrete hollow section simply supported beam shown below have the following…

A: Maximum Bending moment of a simply supported beam with Udl at full span =wl28 StressStrain=Young's…

Q: The prestressed rectangular section shown in cross section in Figure is pretensioned using five low…

A: b = 300 mmd = 430 mmh = 600 mmfpu = 1860 MPafpe = 1140 kN/m2fc = 28 MPaAps

Q: PROBLEM TO SOLVE: 600 mm 400 mm Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: a.…

Q: The column section shown above is reinforced with equal number of 20 mm bars on each face. Using f,…

A: Answer (1) We know that extreme concrete fibres experience strain εc = 0.003 and tension steel…

Q: concrete beam of rectangular section is 10 cm wide and is reinforced with steel bars whose axes are…

Q: A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm…

A: We have to find shear and flexure of beam and axial compression force of beam is 80 KN.

Q: A cantilever slab has a span of 2.40 m. It is 150 mm thick and has an effective depth d = 110 mm. It…

A: Given, span ,l=3 m service live load = 8.5 kPa service dead load = 1.5 kPa compressive strength of…

Q: A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced…

A: The shear force is a surface-sensitive force. The reaction that is induced in a structural element…

Q: Situation no. 1: Calculate the bending stresses in the concrete and the reinforcing steel, using the…

Q: A rectangular beam has the dimensions (see Figure) b- 12 in, h- 20 in, and d- 17 in. and is…

A: It is required to determine the stress in the steel due to 10 ft-k moment.

Q: 6m-simply supported beam cross-section is show in the figure below is prestressed with 15 wires of…

Q: Determine the prestressing steel area required for the precast concrete T-bear Use the following…

Q: The maximum load of 200 KN was applied on a cylindrical specimen of concrete. Find the split tensile…

A: Given data- Maximum load P=200 kN=200×1000 NDepth d=150 mmlength L=300 mmTo Find-The split tensile…

Q: teel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the…

A: According to given data A rectangular beam 250 mm wide, 500 mm deep reinforced at the bottom with…

Q: A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 400 mm.…

Q: 1.) Given the following properties of a rectangular concre strength under the following conditions.…

Q: a-Design the concrete column to carry the applied load Concrete allowable strength: 35 MPa P= 900 kN…

A: Given:- The concrete allowable strength = 35 MPa The magnitude of the load = 900 kN The column…

Q: -kips.

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

3. A one-way slab having a simple span of 3 m is 160 mm thick. The slab is reinforced with
12 mm tension bars (fy=275 MPa) spaced at 140 mm o.c. Steel covering is 20 mm.
Calculate the uniform live load pressure that a slab can carry. Use f'c = 20.7 MPa. Unit
weight of concrete is 23.5 kN/m³.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi. For the midspan section shown, check if steel yields and compute ØM, and compare it with M. WD = 1.2 kips/ft plus weight of beam WL = 1.5 kips/ft %3D 20.5 in 23 in 3 no. 9 bars 18 ft 11 in.
Design a one way slab (as shown in fig) for inside of a building. Normal weight aggregate concrete will be used with a density of 145pcf. Compressive strength of concrete = 4000psi Yield strength of steel = 60000psi LL = 250psf
The beam cross section: Service loads: Steel young's modulus Es = 29,000,000 psi A 1 kN/m distributed load. Concrete young's modulus Ec = 3,500,000 psi A 10 kN concentrated load located at midspan. 10 kN Compressive strength of Concrete f'c = 3500 psi 1 kN/m Tensile strength of concrete f 'ct = 475 psi Steel yield point fy = 60000 psi %3D A 4.0 m 10" 8.0 m y 1. Determine the stress in the steel bars and concrete 23 bottom and top fibers. 25" 2. What value of the 10 kN concentrated load will cause cracks to appear on the concrete? 3. Determine the stress in the steel bars and concrete 3 No. 12 bottom and top fibers if the value obtained in point #2 is increased by 20%.
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
Concrete re in orced a enially with eight steel column bars as shown in Fig. Each bar has diametes of 25 mm It opplied load 4 KN, compute the is 180 Gpa and 3. materi al. Es Stress developed in Ec = 12 Gpa. each 500mm %3D 500mm in
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
PROBLEM TO SOLVE: 600 mm 400 mm 6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa) d. Moment of Inertia under critical condition e. Demand Capacity Ratio of Concrete under Compression Stress f. Compression force on concrete (kN) g. Distance of the compression concrete force from the neutral axis (mm)
Q.1\ A column of a cross-section (350x450)mm is reinforced with 4 bars of (25mm) in diam., knowing that Es=200,000MPa and Ec 22,500MPa and f28MPa and fy = 420 MPa determine the following: 1. The axial load that will stress the concrete to 10 MPa. 2. The normal axial compression strength.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all depth of 536 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 75 mm. The specified compressive strength of concrete is 22.00 MPa. The yield strength of tension reinforcements and stirrups are 404 MPa and 323 MPa respectively.
If column AB is made from high strength pre-castconcrete and reinforced with four 20 mm diameter A-36steel rods, determine the maximum allowable floorloadings P. The allowable normal stress for the highstrength concrete and the steel are (ϭallow)con = 18 MPaand (ϭallow)st= 170 MPa, respectively.