A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches7600 N.Bd3dadsdod₁d2ZEDd5Values for the figure are given in the following table. Note the figure may not be to scale.Variable Valued₁8.5 md₂18.5 m16.5 m30 m9 m80 ma. Determine the magnitude of the force/tension in cord AB, TAB.b. Determine the magnitude of the force/tension in cord AC, TAC.c. Determine the magnitude of the force developed along the tower, FAE-→i. Hint: FAB= (0+03+ FAER) KN.Round your final answers to 3 significant digits/figures.The magnitude of the force/tension in cord TAB isThe magnitude of the force/tension in cord TAC isThe magnitude of the force developed along the tower FAB iskNkNkN

Answered: Image /qna-images/answer/e3f1ce14-1f5a-40b6-b458-1917a0cb9858.jpg

A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches 7600 N. B d₁ E с D 9 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 8.5 m d₂ 18.5 m

A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches 7600 N. B d₁ E с D 9 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 8.5 m d₂ 18.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer completely step by step with brief explanation
Give me right solution From the figure shown, block A weighs 400N and the coefficient of friction between block and the inclined plane is 0.20. Compute the following a) the tension of cable supporting block A if it will have an acceleration of 1.2 m/s2 up the plane. B) the the tension of the cable supporting block B. C) the weight of block B
The following figure shows a simple bracket made of structural steel with Young's modulus E = 200 GPa and Poisson's ratio v = 0.3. The bracket has a cross-section profile shown below and an extrusion depth of 12 cm. A through-hole of diameter 1.5 cm is centered on the bracket's flat ends, one on each side, as shown in the figure. Suppose that the bracket is fixed on the bottom, and lifted by a pressure load of 1,296.12 N/cm² from the inside surface of the top flat portion. What is the total deformation of the bracket in mm? 10.000 1.500 1.500 R3.000 8.000 1.500 12.000 1.500 8.000 All dimensions are in centimeters. 1.500
(b) A solid circular cross-section shaft is clamped at both ends and loaded by a twisting moment t per unit length as shown in figure below. Determine the reactive twisting moment at each end of the bar. ·1 A 13 ◄ t/ unit length C C C C C 1
SITUATION E:A 30 m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg supported for full length. The tape was used in measuring a line 938.55 m long on a smooth level ground under a steady pull of 10 kg. Assuming E= 2x106 kg/cm2 and the unit weight of steel to be 7.9x10-3 kg/cm³. Determine the total correction for increase in tension -0.068 m +0.068 m -0.038 m +0.038 m
1) In the table below; Shear stress, dyn/cm? 0,60 0,81 1,07 8,39 dV/dx1, m/cm.s 0,6 0,81 1,07 8,39 dV/dx2, m/cm.s 0,30 0,67 2,02 5,7 Values for a fluid flowing in a circular pipe are given in the table. a) by writing Newton's law of viscosity, b) Determine the flow behavior of the fluids, show on the graph that they obey the Newtonian or non- Newtonian flow behavior. Calculate the dynamic viscosity values on the graph. c) If the viscosity of the liquid is 0.121 g/cm3, calculate the kinematic viscosity.
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
I need the answer as soon as possible
Climber A is suspended from the rope weighs 75 kg as shown in the figure below. Determine the force in the rope connecting A and B.
The simply supported beam AB shown in the diagram has a length L=8 m and subjected to a uniformly distributed load q = 4 kN/m, a point load P = 16 kN located at a distance a = 0.3*L m from support A and a moment M = 14 kN.m located at distance d=0.8*L m from support A. What is the value of the bending moment under the point load P. Give your answer to one decimal place. M d
Please complete the prodecure and the solution and the figure. Please list the given and the formula that had been used. Box the answer. Find acceleration in ms/s^2 Find the tension in the cable in N
urgent please solve in 1 hour and get upvote and 5 star review You have to solve it but urgent