The simply supported beam AB shown in the diagram has a length L-8 m and subjected to a uniformly distributed load q - 4 kN/m, a point load P - 16 kN located at a distance a - 0.3"L m from support A and a moment M = 14 kN.m located at distance d-0.8°Lm from support A. What is the value of the bending moment under the point load P. Give your answer to one decimal place. M

The simply supported beam AB shown in the diagram has a length L-8 m and subjected to a uniformly distributed load q - 4 kN/m, a point load P - 16 kN located at a distance a - 0.3"L m from support A and a moment M = 14 kN.m located at distance d-0.8°Lm from support A. What is the value of the bending moment under the point load P. Give your answer to one decimal place. M

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q2: For the cantilever beam with uniformly distributed load shown in Figure 2. Use the data…

A: As per guidelines we are supposed to answer only first 3 subparts of question so please repost rest…

Q: The uniform load has a mass of 600 kg and is lifted using a uniform 30-kg strongback beam BAC and…

A: Consider the following free body diagram: The given system is symmetrical, thus the tension in each…

Q: A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N…

A: Given:- L = 750 mm P = 800 N allowable bendingstress =120 MPa. To find:- (a) Determine the required…

Q: Determine the maximum positive moment that can be developed at point D in the beam shown in figure…

Q: 1) Draw the shear force and bending moment diagrams. 2) Determine its required diameter if oallow =…

Q: A distributed loading of q(x) = (10x1/2 + 160x + 10) Pa acts over the top surface of the beam of…

Q: For the frame below, F = 9.2 kips, a = 6 ft, b = 5 ft, and c = 3 ft. Determine the magnitude of the…

A: Given: The value of F is 9.2 kips. The value of a is 6 ft. The value of b is 5 ft. The value of c is…

Q: Problem I Compute for the moments at support of the beam loaded as shown : OMA INKEE А SMA RA P = 40…

Q: Consider the beam shown in (Figure 1). Suppose that P = 6 kip, w = 1.2 kip/ft. Point E is just to…

Q: The beam in the following figure is level before the distributed load is applied. The maximum moment…

Q: Determine the maximum bending moment along the length of the bear

Q: Consider the beam shown in (Eigure 1). Suppose that P = 3 kip, w = 1.1 kip/ft. Point E is just to…

Q: Situation 3: A simply supported beam carries a concentrated load P placed at midspan. Determine the…

Q: The figure shown is a continuous beam which carries ultimate of factored uniform load of 12 kN/m…

A: Moment : The moment is an expression that accounts for how a physical quantity is located or…

Q: Situation 4: As shown in the figure, a load P is supported by the tripod. If the force in any leg is…

A: Find out the forces on each member:Taking co-ordinates of each…

Question

The simply supported beam AB shown in the diagram has a length L=8 m and subjected to a uniformly distributed load q = 4 kN/m, a point load P = 16 kN located at a distance a = 0.3*L m from support A and a
moment M = 14 kN.m located at distance d=0.8*L m from support A. What is the value of the bending moment under the point load P. Give your answer to one decimal place.
M
d

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported beam made of 360UB56.7 (300 Plus) section. The beam has got full lateral support at the ends and the middle. There is no rotational restraint. The bending moment diagram for the applied loads is shown in Figure 3. Assume that the load is applied through the shear centre of the cross-section of the beam. Calculate the safety factor for the given load. The safety factor is defined as ??????∗.
Problem Sets: 3) A truck and trailer combination having the axle loads as shown in the figure rolls across the simply supported beam with a span of 12 meters. Determine the maximum shear force and bending moment and draw the shear and bending moment diagrams where the maximum moment occurs. whim P3=40 KN 4m HH₂ P1=20 kN 2m P2=30 kN 12m 2m P3=30 kN
Determine the maximum shear and moment for the beam shown below. 14 kN/m 7 kN/m 7 kN/m A D В C 3 m- 4 m - – 3 m ANSWER: Vmax = KN (use up to 3 significant figures) Mmax = KN.m (use up to 3 significant figures)
Part 1: Calculate the design ultimate bending moment M* The cantilever beam, shown in Figure 1, carries a uniformly distributed live load Q of 3 kN/m and a uniformly distributed superimposed dead load G of 2 kN/m, in addition to its self-weight (density is 2400 kg/m³). A point load P of 10 kN is permanently applied in B (see Figure 1). The width and the total depth of the beam are 200 mm and 400 mm respectively. The beam span L is equal to 3m. Consider the appropriate load factors and combinations at Ultimate Limit State to calculate the design ultimate bending moment M". 400 mm 200 mm W Figure 1: Cantilever beam subject to uniform distributed loads and point load.
Absolute maximum bending moment in beam AB shown in the figure below, due to the given moving load, equals * 25kN 50KN -8.0 m- O 102.4 kN.m O 106.3 kN.m O 100.1 kN.m 104.2 kN.m
10 A rectangular beam 200mm deep and 300mm wide is simply supported over a span of 8m. What uniformly distributed load per metre the beam may carry, if the bending stress is not to exceed 120N/mm². w/m length w.L w.L Figure 7 300 mm 200 mm
Question 3 A compound beam is connected by a pin at B, and a pin in a slot at C, and loaded as shown. Couple moment M = 500 N.m, force F= 2500 N, the triangular distributed load has a peak intensity w = 1200 N/m. Force F acts at an angle 0 = 60°, while the beam dimensions are such that a= 1.0 m, b = 0.5 m, c = 1.0 m, d= 1.5 m, e = 1.0 m, f= 2.0 m, and g= 1.0 m. M while E D Determine: a) the horizontal and vertical components of the pin reactions at B and C, and b) the normal force, shear force, and bending moment acting at point F of the beam.