Note: If you got answer other than options, please leave it question.A nozzle discharges 155lit/sec with a velocity of 35m/s. The entire jet strikes a vane moving in the same direction as the jet with a velocity of 20m/s. Compute the Force exerted on the vane. A nozzle discharges 155lit/sec with a velocity of 35m/s. The entire jet strikes a vane moving in the same direction as the jet witForce exerted on the vaneha velocity of 20m/s. Compute the30 degO 1924.131294.31O 1429.13O 1942.13

Answered: Image /qna-images/answer/7b7afb56-6ec2-4c2e-a39e-8fc3c702dd37.jpg

Answered: A nozzle discharges 155lit/sec with a…

A nozzle discharges 155lit/sec with a velocity of 35m/s. The entire jet strikes a vane moving in the same direction as the jet with a velocity of 20m/s. Compute the Force exerted on the vane.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two identical pumps connected in series using a pipe 3.5 cm diameter with water flowing at velocity 2.5 m/s The reading of the pressure gages G1=0.1 bar and G2 =0.6 bar. What is the head (m) rise in water caused by the TWO pumps? GI GZ G3 Pump Pump 8-02 PM ENG 8/26/2021 94°F Lenovo K9 Note Al Dual Camera
Problem 2: Consider the nozzle, below, for which the cross sectional area changes linearly from the base to the tip. Water flows through this nozzle at a constant discharge rate of 0.1 m³/s. What is the A) mean fluid velocity ta point that is 12 cm away from the outlet, and B) the fluid acceleration at a point that is 12 cm away from the outlet? Your solution must include assumptions as well as a sketch of the control volume with open and closed control surfaces indicated along with area vectors for the open control surfaces. 9-cm diameter 36 cm- 3-cm diameter
Subject: Hydraulics What size of brass pipe would be required to carry standard gasoline at 80 degree Fahrenheit at a velocity of 10 ft. per second with a loss of head of 15 ft. per 100 ft?
A 10-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless flow, find the force FB exterted by the flange bolts to hold the nozzle on the hose. O 2728 N O5861 N Water: 1000 kg/m³ O 3566 N O 4067 N D₁ = 10 cm Pa = 0 (gage) Hint: One-dimensional momentum flux: F = ploutvout - Plin Vin (2) D₂ = 3 cm CV
... 300 mmg 100 mmø H20, 500mm EHgC(13-6) A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss. (A) No Answer among the choices (B) 94.12 L/s 82.44 L/s 77.36 L/s (E) 87.86 L/s
7.12 The globe valve in the pipeline shown is opened instantaneously. If the loss coefficient for the wide-open valve is 3.0, how many seconds are required for the velocity to reach 99% of its final value? Neglect the entrance loss. El. 1000' El. 980' - 2000'12" f = 0.018 XIO El. 970' Valve
Moving to another question will save this res ion 39 A 128-mm-diameter pipe enlarges to a 146-mm-diameter pipe. At section 1 of the smaller pipe, the density of gas in steady flow is 263.178 kg/m3, and the velocity is 22 m/s; at section 2 of the larger pipe, the velocity is 15 m/s. Find the unit weight (in kN/m3) of the gas at section 2. Round off to three decimal places. < Question 39 of 48 A Moving to another question will save this response. F12 PAUSE కాజా F10 F11 DELETE F4 FS F6 F7 FB F9 F2 F3 BREAK F1 ESC % $ 4 NUM LK @ %23 5 6 { } Y P HOME ENTER G H J K A SHIFT V CTRL V 因

A nozzle meter is another device used to determine the flow velocity and flow rate in pipe. The nozzle meter installed in a pipe shown in Figure 4 is horizontal. Derive the equation for the flow velocity and the flow rate in the pipe. (1) Nozzle P,V d2 Pipe Figure 4 Cs Scanned with CamScanner
uservoir discharges into a 55-inch pipe that discharges freely, as shown below. What is the pressure in the pipe at point A? Consider friction. Use f =0.02 Elev 155 ft Inv. @ A 134.2 ft 55 in 140 ft Inv. 120 ft 420 ft 900 ft 1450 ft a. 502 psf b. 502 psi c. 457 psf d. 457 psi e. 36 ft ,what is the velocity at point B? a. 17.5 fps b. 36 fps c. 3.6 fps d. 4.57 fps e. 50.2 fps ar
Example 1: A flow of water from a reservoir to a pipe of different diameters shown in Figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the energy and hydraulic grade lines. water 10m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel)
A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time will be 5 seconds. The system operates with a pressure of 50 psig (3.45 bar) and there will be a pressure loss of 2 psi. What will be the Cv of the valve to be installed? [Answer: 1.99]