1. If the pump removes 12 ft /min of water from a tank, how long will it take to empty the tank if it contains 20000 lb of seawater @ 25°C? 2. A standard schedule 40 steel pipe is to be selected to carry 10 gal/min of water with a maximum velocity of 1 ft/s. what size pipe should be used (inches)? 3. A venturi meter is a device that uses a constriction in a flow system to measure the velocity in flow. The figure below illustrates one type of design. If the main pipe section is a standard hydraulic copper tubing having an outside diameter of 80 mm and a wall thickness of 2.5 mm wall thickness, compute the flow rate when the velocity is 4 m/s. Then, for that volume flow rate, specify the required size of the throat section that would make the velocity there at least 15 m/s. Main pipe section 1 Throat section 2 Main pipe section 3 D. Flow Manometer

1. If the pump removes 12 ft /min of water from a tank, how long will it take to empty the tank if it contains 20000 lb of seawater @ 25°C? 2. A standard schedule 40 steel pipe is to be selected to carry 10 gal/min of water with a maximum velocity of 1 ft/s. what size pipe should be used (inches)? 3. A venturi meter is a device that uses a constriction in a flow system to measure the velocity in flow. The figure below illustrates one type of design. If the main pipe section is a standard hydraulic copper tubing having an outside diameter of 80 mm and a wall thickness of 2.5 mm wall thickness, compute the flow rate when the velocity is 4 m/s. Then, for that volume flow rate, specify the required size of the throat section that would make the velocity there at least 15 m/s. Main pipe section 1 Throat section 2 Main pipe section 3 D. Flow Manometer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hydraulics of Sprinkler Nozzle Example// Select the diameter of the nozzle and the working pressure for a sprinkler has a discharge of (126 m2/hour)?
Use 4 decimal places in all the computations.
please show all working and the assumptions and equations used to get final answer
I need the answer as soon as possible
please sir, will appreciate it all
fluid mechanix/hydraulix
Hello! Kindly answer the problem attached image below. Thank you! ASAP
Water at 50°F is pumped from a lake at 750 gpm through a length of 3-inch schedule 40 commercial steel pipe as shown below. The inlet to the pipe is eight feet below the surface of the lake. A 25-HP gasoline engine drives the pump and the pump has an efficiency of 80% What is the Reynolds number in the pipe? Is the flow laminar or turbulent? What is the head added to the water by the pump? What is the head loss due to pipe friction?
Part 1 Part 2 Part 3 hp A centrifugal pump having a 7.5-in-diameter impeller and the characteristics shown in the figure below is to be used to pump gasoline through 4000 ft of commercial steel 3-in.-diameter pipe. The pipe connects two reservoirs having open surfaces at the same elevation. Determine the flowrate. Do you think this pump is a good choice? This figure is referred to as the pump performance characteristics. 500 8 in. dia 400 7 出300 6 Head, ft 200 100 65 60 55 50 40 bhp 30 25 20 80 ° 40 120 160 200 240 280 320 Capacity, gal/min Write the system equation for this flow system as function of the friction factor f and volume flowrate Q in gal/min. (Use 2 significant digits on coefficients. Do not enter units as a part of your response.)
PLEASE HELP ME ANSWER THIS ASAP. NOTE: COMPLETE SOLUTION WITH PROPER FIGURES. 3 DECIMAL PLACES
A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time will be 5 seconds. The system operates with a pressure of 50 psig (3.45 bar) and there will be a pressure loss of 2 psi. What will be the Cv of the valve to be installed? [Answer: 1.99]
Fluid mechanics