A 10-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless flow, find the force FB exterted by the flange bolts to hold thenozzle on the hose.O 2728 NO5861 NWater:1000 kg/m³O 3566 NO 4067 ND₁ = 10 cmPa = 0 (gage)Hint: One-dimensional momentum flux: F = ploutvout - Plin Vin(2)D₂ = 3 cmCV

D1 = 10 cm D2 = 3 cm Q = 1.5 m3/ min.Patm = P2 = 0 we have to find- The force (FB) exterted by the…

0-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless flow, find the force FB exterted by the flange bolts to hold the Ele on the hose. 2728 N Hint: One-dimensional momentum flux: F = PQout Vout 5861 N 3566 N Water: 1000 kg/m³ #067 N D₁ = = 10 cm Pa = 0 (gage) - D₂ = 3 cm CV PQin vin

0-cm fire hose with a 3-cm nozzle discharges 1.5 m3/min to the atmosphere. Assuming frictionless flow, find the force FB exterted by the flange bolts to hold the Ele on the hose. 2728 N Hint: One-dimensional momentum flux: F = PQout Vout 5861 N 3566 N Water: 1000 kg/m³ #067 N D₁ = = 10 cm Pa = 0 (gage) - D₂ = 3 cm CV PQin vin

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2
Assume that the pin B connected to the linear actuator starts from rest when 0= 0° and accelerates with a constant acceleration of aB = 0.2m/s² in the direction shown. Calculate and plot the angular velocity Ô and angular acceleration Ö of the arm from time t = 0 to time t= 2 seconds. ав 30° 0.5m ----
The system shown in figure has a right ward velocity of 3 m/sec. Determine its velocity after 5 seconds. Take u = 0.2 for the surfaces in contact. Assume pulleys frictionless. 500N 1000N 30 2000N (a)
Block A has a mass of 100 kg and a coefficient friction of 0.30. Determine the friction force acting between A and B.
Show complete and neat solution
Hello Your answer is 690.723 /s But correct answer is: 345/s Please check for me please.
Find the value of EIS at the left end. Use area-moment method.
find the flow rate of water through the sytem shown forthe turbine to produce 20 kW. Neglect Friction in your calculations. Q=10.73m^3/s P=204kw/273hp
s [pis. The velocity of the water jet discharging from the orifice can be obtained from v = V2 gh, where h = 2 m is the depth of the orifice from the free water surface. Determine the time for a particle of water leaving the orifice to reach point B and the horizontal distance x where it hits the surface. 2 m 1.5 m
Semi-circular gate AB is used to store kerosene as shown. Calculate the magnitude of the resultant hydrostatic force, in kN, acting on gate AB. Kerosene SG= 0.82 5 m 3 m A B -P Gate: Side view
Please help me draw the influence line using Equilibrium equation solution.
Solve the Ff. Publems yolumnted I w A Pitot-státic tube (c, : 1.6) is used to air speed wsth water in dipfertntial manometer and. a gage dipperen ce of 100mm,calculate the äir Jair= 12 Mm3 the measure air! impéed using