Just after the fan is turned on, the motor gives the blade an angular acceleration a = (20e-0.6t) rad/s², where t is in seconds. Determine the speed of the tip P of one of the blades when t = 3 s. How many revolutions has the blade turned in 3 s? When t = 0 the blade is at rest. 1.75 ft

Q: What the deviator stress?

A: The deviator stress can be defined as it is the difference between the principal major and minor…

Q: Describe surface grinding operation.

A: To achieve a smooth appearance, surface grinding is performed on flat surfaces. Grinding is indeed a…

Q: Define differential hammer,

A: Differential hammers are the same as a double-acting hammer. these hammer having a simpler value…

Q: What are the two classes of adhesives?

A: Adhesives are defined as the material that is used to connect, join or stick two different objects.…

Q: Explain the minimum diameter of bar used in column ?

A: There are different shapes of bars are used in the construction. it is used to enhance the bond…

Q: Please answer it asap thanks!! Q2ii. During the Defects Liability Period, the Contractor is still…

A: Defects liability period It is a fixed time period, starting from the date of practical completion,…

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps.

A:

Q: Q4: Prove that:

A:

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: Define the term Fastener Spacing?

A: Fastener Spacing : Pitch is centre to centre spacing of the fasteners in a row, measured along the…

Q: What is layerd cake

A: Layered cake:

Q: Describe the auger method.

A: Auger method:

Q: The information shown in this attached document. This has been extracted from the Expert Panel…

A: The order of construction in civil projects can vary depending on the specific project and its…

Q: Situation 21: A square tied column carries a factored load of 2800KN. It will be designed using…

A: Columns are structural members which carry compression loads transferred from the beams and slabs.…

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: Define Allowable Stress Design

A: Their are mainly two type of design concept: Allowable stress method Load and resistance factor…

Q: 6.2 THE FOLLOWING PROVISIONS IN A CONSTRUCTION CONTRACT ARE UNENFORCEABLE: CHECK ALL CORRECT…

A: UNENFORCEABLE  means the clause in a contract that cannot be legally upheld by lawIt means if one…

Q: Define the size of a concrete cube?

A: Cube test of concrete is one of the most important tests done on concrete. It is also known as a…

Q: Define induced stresses ?

A: The internal resistance of a body to changes and deformation due to applied load is known as stress.…

Q: Prepare a complete NC program for finishing profile shown in fig.2 with continuous cut in clockwise…

A:

Q: Define why Load cells are used ?

A: Load  cells are transducers that are generally used in electronic weighing machines these are mainly…

Q: Design the most efficient, rectangular, concrete (n=0.015) channel to carry a flow of 2,500-ft³/sec,…

A:

Q: = What is the gage pressure [in psi]... Water Air Oil (SG=0.8)

A: Given:Required:Gage pressure at bottom of tankGage pressure in the air zone in the container

Q: List the points that are pertinent in the care of tapes.

A: In surveying most of the measurements is done with the help of tape, following are some pertinent in…

Q: he accuracy of the spread plate metho

A: The spread plate method is generally the technique to plate the sample of liquid that contains…

Q: Define Normal load,

A: The load that acts perpendicular to the contact surface is known as a Normal load. In  simple cases…

Q: Evaluat the fllowing limits Lim X # a X>a X - a

A: Given values -  limx→a = x2+1 - a2+1x-a     ,    x ≠ a   Rule -  The above problem can be solved by…

Q: What is the types of shrenkage ?

A: Shrinkage is characterized as the contracting of a solidified solid combination because of the…

Q: Describe the term compressibility.

A: Compressibility:- It is defined as the capability of the soil to decrease its volume under…

Q: ESSAY Advantages and Disadvantages of Using Hollow Block

A: Hollow blocks are generally prepared with aerated concrete . These block have both advantages as…

Q: Find the moment of inertia (Ix, mm“) of the composite shape from the bottom base. Type answer in two…

A:

Q: Compute the net area A, of the shape shown. Report your answer in in to the nearest two decimal…

A:

Q: RUCTURAL SAFE

A: Structural-Safety brings together the work of CROSS and SCOSS to collaborate with the professions,…