A mobile home served with 120/240 volt 3 wire service that has a calculated load greater than 50 ampere is required to be supplied power using a permanent wire method from the adjacent power supply pole to the mobile home. The power supply feeder is required to consist of?

Q: What size conductor should be used in a 2-wire system to service a load of 6,500 watts, 150 feet…

A:

Q: what wire size is needed on a one 20 amp, 120-volt laundry branch circuit? what wire size is needed…

A: 12 gauge what wire size is needed on a one 20 amp, 120-volt laundry branch circuit.

Q: Give the raceway size required for each of the following conductor combinations: 1. Five, 10 AWG,…

A: The raceway size  required for each of the following conductor combination is given as per the…

Q: A DC motor that draws 7.2A is located 85 feet from its 240VDC source. The copper conductors…

A: Given Voltage V = 240 V Current I = 7.2 A Length L = 85 ft Voltage drop = 2%

Q: What code sets standard for the electrical installation work?

A: We habe to find code for electrical installation work

Q: Conductors shall be arranged so the power distribution block terminals are _____ following…

A: In the National Electrical Code (NEC), information about power distribution block is mentioned.…

Q: Describe the standard operating procedure (SOP) for Power Supply. including precautions too. Thank…

A: The standard operating procedures for the power supply are listed below:  1- Before the power supply…

Q: 10. Which of the following statements about ground faults is true? A. They usually occur between any…

A: Ground faults: It happens when an energized conductor develops an accidental contact with the…

Q: 5. How many system bonding jumpers normally are there for a separately derived system that's…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub- parts…

Q: 1.1 PV modules can be wired together in an array using ______ connections to increase voltage. a.…

A: In this question,  We need to choose the correct option Which method will be prefere to increase the…

Q: 19. What size copper bonding jumper must be used in an AC electrical system that has 500 kcmil…

A: 20. Answer:D.busbar  A neutral  disconnect link is usually in the form of a busbar or a terminal to…

Q: Which of the following is an approved disconnecting means for a feeder or branch circuit supplying a…

A: The disconnecting means for a feeder or branch circuit supplying a separate building or structure is…

Q: 1.a. Section 300.15(C) requires a fitting to be installed on each end of a conduit or tubing being…

A: 1.a. According to NEC section 300.15(C), A conduit or box body shall not be required where cables…

Q: Connect the initial circuit as shown in Figure 47-1. 2. Set VA at 20 volts. Insert a jumper wire…

A:

Q: Four No. 12 and four No. 10 conductors are to be installed in a EMT conduit. What size EMT conduit…

A: Conductors size is selected on the basis of assigned numbers.  As the assigned number increases then…

Q: What code sets stabdard for the electrical installation work?

A: In the following section, the code which sets standards for electrical installation work has been…

Q: . You're installing type AC cable. The armor coating of type AC cable is allowed for use as an…

A: Requirement for the installation and constructions for AC 'Armored cable' are located in Article…

Q: . A grounded circuit conductor and the equipment grounding conductor should always be joined at the…

A: Choose the correct option A grounded circuit conductor and the equipment grounding conductor should…

Q: Explain how electricty power is generated and tramnsimitted to customer unit. Show The single line…

A: The electrical power is generated and transmitted to the consumer : The electrical power is…

Q: Seven 8 AWG copper conductors are run in conduit. Each conductor has type THHN insulation. The…

A: Given Copper wire AWG =8 total number of copper wires =7 Type of insulation THHN Ambient temperature…

Q: testing installation of grounds, the usual procedure is to connect one lead of the megohmmeter to…

A: Megohmmeter is an instrument use for the measurement of very high resistance such as insulation…

Q: 1. Alternating current systems of less than _______ volts are required to be grounded if they're…

A: Alternating current systems of less than _______ volts are required to be grounded if they're…

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.