1.a. Section 300.15(C) requires a fitting to be installed on each end of a conduit or tubing being used to provide support or protection to protect the cable from A. hazardous vapors. B. direct sunlight. C. abrasion. D. extreme heat or cold. 1.b. Typically, a/an _______ is a better electrode than a ground rod because it provides a greater surface area from which the electrons can be dissipated. A. continuous grounding conductor B. clamp-on ground resistance meter C. rebar D. OCPD

Q: The National Electrical Code® _____ contains tables dealing with conductors for general wiring.…

A:

Q: Six 1/0 aluminum conductors are to be run in a conduit. Each conductor has type THWN insulation's,…

A:

Q: The bonding conductor or grounding electrode conductor for communication circuits, shall not be…

A: Grounding electron conductor  : The grounding electrode conductor connect grounding electrode to the…

Q: When installing grounding electrode conductor at services, it's common to use a single large common…

A: Here we discuss about grounding/earthing related concept.

Q: Give the raceway size required for each of the following conductor combinations: 1. Five, 10 AWG,…

A: The raceway size  required for each of the following conductor combination is given as per the…

Q: The ohms per 1000 feet measurements for conductors can be found in _____. Select one: a. article…

A: The obstruction offered to the smooth flow of current is called resistance. The electrical element…

Q: Amprobe Clamp-On Meter (Model RS-3) How many conductors should be in the jaws of the meter when…

A: Only one individual question is to be answered. So, kindly repost the remaining questions. 1. The…

Q: Several factors or conditions can cause conductors to overheat, but often overlooked is the…

A: The heating is the major concern in the conduction as the temperature increases then the resistance…

Q: A DC motor that draws 7.2A is located 85 feet from its 240VDC source. The copper conductors…

A: Given Voltage V = 240 V Current I = 7.2 A Length L = 85 ft Voltage drop = 2%

Q: Airframe Electrical System Question: In general, what factors areconsidered when selecting the…

A: While manufacturing, the sizes of the wire are selected according to a known standard called as…

Q: 10. Which of the following statements about ground faults is true? A. They usually occur between any…

A: Ground faults: It happens when an energized conductor develops an accidental contact with the…

Q: Give the raceway size required for each of the following conductor combinations: 1. Five, 10 AWG,…

A: Given information, Number of conductors=5. Type of insulation is THW. Size of wire=10 AWG. Raceway…

Q: 1.1 PV modules can be wired together in an array using ______ connections to increase voltage. a.…

A: In this question,  We need to choose the correct option Which method will be prefere to increase the…

Q: 19. What size copper bonding jumper must be used in an AC electrical system that has 500 kcmil…

A: 20. Answer:D.busbar  A neutral  disconnect link is usually in the form of a busbar or a terminal to…

Q: Underground service conductors shall have [Fill-in-the-blank]. A)adequate mechanical strength.…

A: According to the section 230.31 Underground service conductor shall have sufficient ampacity for the…

Q: Connect the initial circuit as shown in Figure 47-1. 2. Set VA at 20 volts. Insert a jumper wire…

A:

Q: . You're installing type AC cable. The armor coating of type AC cable is allowed for use as an…

A: Requirement for the installation and constructions for AC 'Armored cable' are located in Article…

Q: 14. Which of the following is a condition that must be met in order to qualify for the exemption…

A: Since #14 and #17 are two different questions, as per the guidelines, #14 has been solved in the…

Q: . A grounded circuit conductor and the equipment grounding conductor should always be joined at the…

A: Choose the correct option A grounded circuit conductor and the equipment grounding conductor should…

Q: Seven 8 AWG copper conductors are run in conduit. Each conductor has type THHN insulation. The…

A: Given Copper wire AWG =8 total number of copper wires =7 Type of insulation THHN Ambient temperature…

Q: How can lighting fixture be ground and what size of the conductor can be used

A: There are so many things that come in our mind which is related to light. It may be an artificial…

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.