A metal wire of diameter 1.2 mm is used to carry a load of 1100 N. If the material of which the wire is made has a yield point of 950 MPa ultimate tensile strength of 1425 MPa then is this wire suitable for carrying that load? If yes, then support your answer with calculations and explain your results. If the answer is no, then explain why with calculations and calculate the required diameter of that wire to carry that load.

Q: A 30-mm-diameter popper rod is 1 m long with a yield strength of 70 MPa. Determine the axial force…

A: Given data  Diameter = 30 mm  Length = 1m  Yield strength = 70 Mpa

Q: A rod made of aluminum alloy, with a length of 150 mm, diameter of 15 mm, and yield strength of 160…

A:

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A: Given,  The longitudinal force in all member is same due to law of transmibility

Q: 8.22 Consider the brass alloy for which the stress-strain behavior is shown in Figure 8.12. A…

A:

Q: steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter . The internal diameter of…

A:

Q: A steel plate, which has a fracture toughness in a plane strain state of 83 MPavm, is alternately…

A: Given Data: KIC=83 MPamσmax=750 MPaσmin=20 MPaf=1n=2.8ai=0.0015 mm   To Find: Determine the value of…

Q: One piece is made of a metal alloy with a yield limit of 180 MPa. At a certain point in the part…

A:

Q: A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of…

A:

Q: A 10 mm diameter wire cable is being used to lift a crate of parts. If the cable is made from…

A:

Q: A tensile stress is applied along the long axis of a cylindrical brass rod thathas a diameter of 10…

A: if you have any doubt please comment

Q: . Consider a cylindrical nickel wire 0.08 in. in diameter and 1200 in. long. Calculate its…

A:

Q: Calculate the thickness of metal necessary for a cylindrical shell of internal diameter 160 mm to…

A: To findCalculate the thickness of metal necessary for a cylindrical shell.GivenInternal diameter, d…

Q: Calculate the Young Modulus for a mild steel. When a rod of the steel is being tested under tensile…

A: Given : L = 4.5 m = 4500 mm d = 35 mm ∆L = 0.9 mm P =50000 N E = ?

Q: A solid cylindrical metal of 130 cm tall and 30 mm thick is centrally bored for 0.3 m, the bore…

A:

Q: A steel rod of diameter 40 mm is subjected to a axial load of 60 N. The length of the rod is 10 m…

A: Given data: - The diameter of the rod is d = 40 mm. The axial load is P = 60 N. The length of the…

Q: Calculate the modulus of elasticity of the following material if it has a design stress of 250 kPa,…

A:

Q: Explain the ductile material property using a neat stress-strain diagram with two practical…

A: Data given-  Dutile material : dutile material are those solid material who can show the substantial…

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: Evaluate bulk modulus, if modulus of rigidity and Poisson’s ratio for a material are 75 GPa and 0.3…

A: Modulus of rigidity, G=75GPa Poisson's ratio, μ=0.3

Q: A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension with…

A:

Q: A tensile force of 200 KN is applied on a 0.02-m diameter and.2-m long rod. After applying the load,…

A:

Q: Consider a cylindrical nickel wire 1.6 mm in diameter and 3.5 × 104 mm long. Calculate its…

A:

Q: A tensile force of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A: The original diameter of the shaft=0.02m=20mm Force applied =P=120kN We need to find The engineering…

Q: A 8mm diameter rod, of unknown material, is subjected to 50kN tensile load. In the process, its…

A: GIVEN DATA Diameter d=8mm Load P=50KN Initial length =300mm final length = 303mm

Q: A cylindrical material that has a Young’s Modulus of 2.5 GPa that is loaded along its longitudinal…

A:

Q: The five-bolt connection must support an applied load of P = 2600 Ib. If the average shear stress in…

A:

Q: consider a cylindrical nickle wire 1.9 mm in diameter and 3.0*104 mm long. calculate its elongation…

A:

Q: Consider a cylindrical nickel wire 2.7 mm in diameter and 12 m long. Calculate its elongation when a…

A: Given Data Wire diameter, d=2.7 mm Length of the cylindrical nickel wire, L=12 m Load=930N Modulus…

Q: What are the internal forces F1 and F2 in rods (1) and (2), respectively?  Use the sign convention…

A:

Q: A 35 kN axial load is applied to a metal bar with a rectangular cross-section, 28mm wide by 10mm…

A: To find: The original length of the bar. Given: The load is P=35 kN. The width is 28 mm and…

Q: A cylindrical metal rod of 20mm diameter and 1m length is subjected to a tensile load of 60KN. To…

A:

Q: A steel rod with a cross-sectional area of 150 mm² is stretched between two fixed points. The…

A:

Q: In a sheet metal of 2 mm thickness, a hole of 10 mm diame- ter needs to be punched. The yield…

A:

Q: The cable of hoist has a cross sectional of 80mm2.The hoist is used to lift a crate weighining 500…

A: Given    Area, A = 80mm2    Load, P = 500 kg Length, L = 30 m Find   1. stress on the cable   2.…

Q: Give ONLY the correct answers with their units A. Calculate the axial deformation of a steel rod 20…

A:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.