A cylindrical metal rod of 20mm diameter and 1m length is subjected to a tensile load of 60KN. To what length the cylinder should be centrally bored on one side to reduce weight by material removal, so that the total extension will increase by 10 percent under the same pull. The diameter of the hole being bored on

Q: A hollow cylindrical rod with a diameter of 100mm and a thickness of x tensile load of 12.5 kN. Find…

A: Given data:

Q: Calculate the maximum stress in a 5mm thick steel plate with an 18 mm diameter round hole, given h…

A: Given,Thickness of steel plate = 5 mmH gross = 12 cmTensile load = 8.5 KNTo find - maximum stress in…

Q: A thick walled cylinder with an inner diameter 44 mm and an outer diameter 70 mm is made from a…

A: To find: The pressure will the cylinder initially yields. Given: The inner diameter is di=44 mm and…

Q: Problem 2: The short cylindrical block of 2014-T6 aluminum, having an original diameter of 0.5 in.…

A: Given:d=0.5 inL=1.5 inP=800 lbE=10.6*106 Psiμ=0.35

Q: A 400 ft long elevator cable (diameter of 1 inch) is made of 4130 steel with a yield strength of 120…

A:

Q: A tensile stress is applied along the long axis of a cylindrical brass rod thathas a diameter of 10…

A: if you have any doubt please comment

Q: hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of…

A:

Q: If you don't know the solution please leave it for someone.  The tensile strength of a 6-in. thick…

A: Given: The tensile strength of slab = 450 psi The thickness if slab, t = 6 in

Q: A load of 20 kN is applied to a rod with a diameter of 12.5 mm. Calculate the strain in the rod if…

A: Given Data: The load applied, P=20 kN Diameter of the rod, d=12.5 mm Young's modulus, E=103 GPa

Q: the ground and free in the upper end. a) Calculate the compressive stress, then the minimum…

A: Given Data: H=3 mm=1000 kgFOS=3σut,c=241 MPaE=190 GPa   To Find: (a) The compressive stress. (b) The…

Q: The is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without…

A: Given: Tensile force applied on the rope, T=500 N mass of the rope, m=0.5 kg length of the rope,…

Q: A steel rod of diameter 40 mm is subjected to a axial load of 60 N. The length of the rod is 10 m…

A: Given data: - The diameter of the rod is d = 40 mm. The axial load is P = 60 N. The length of the…

Q: A load is applied to a rigid bar that is symmetrically supported by three steel rods, as shown. The…

A: here the cross- section of the rod is A  A= 1.2 in2 stress = 22000 psi

Q: A bar is applied a tensile load of 50 kN having diameter 10 mm,  Calculate the tensile stress induc

A: Given:force, F=50 kNdiameter, d=10 mm

Q: The one end of a hollow square bar whose side is (10.50) in with (1.50) in thickness is under a…

A: Given data: The side of the square bar is a=10.5 in The thickness of the bar is t=1.5 in The tensile…

Q: A 5-mm thick mild steel plate is used to form a hollow column of 60 mm outside diameter.  The column…

A: Givenhollow columnone end is hinged and the other end fixed.t=5mm=0.005mD=60mm=0.060mL=1.2mE=206…

Q: Calculate the percentage elongation of a steel rod, when it is subjected to an axial pulling force…

A:

Q: The steel rod is stress-free before the axial loads P = 150 kN are applied to the rod. Assuming that…

A:

Q: The link shown, made of steel with y-410MPa and E-200GPa is subjected to a tensile load of 30kN. Let…

A:

Q: When a hydraulic cylinder is firmly anchored and pushing on a guided load, the effective length of…

A: Effective length of rod (le)= 2 m =2000 mm Diameter of rod (d)= 3.8 cm= 38 mm yield stress for 304…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A:

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A:

Q: Determine the maximum safe load that can be applied to the bar shown in Figure 3(b) if a safety…

A:

Q: A member in tension in a machine frame is subjected to a continuous load of 5.00 kN. Its length is…

A: Given data  Length of member = 750 mm Load = 5.00 kN Outer diameter = 17 mm Inner diameter = 12 mm…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A:

Q: 1. A hollow steel tube of external diameter 100mm and a wall thickness 12mm is subjected to an axial…

A:

Q: A 125 long bar with a cross section of 12.7 mm by 3.2 mm is exposed to a 1560 N tensile load.…

A: Write the given information.

Q: steel strut with built-in ends has a rectangular cross-section with width twice the thickness and a…

A:

Q: A steel bar of diameter 1cm and length 10cm is made of steel E=200Gpa and yield strength of 300Mpa…

A:

Q: A steel rod with a cross sectional area of 120mm2 is stretched between two fixed points. The tensile…

A:

Q: A cylindrical shell is pressurised to 2 kN/mm², and has an internal diameter of 556 mm. If the…

A:

Q: A steel rod of 30 mm diameter is subjected to a 10 kN of axial load. The length of the steel rod is…

A:

Q: with a stress of 52.89  and diameter of 4cm and thickness of 2mm  (P) load of 2MPa how was the…

A:

Q: A steel rod of length 10 m is subjected to a axial load of 10 kN. Calculate the elongation of the…

A: Given data  Length of steel rod (L) = 10 m  Axial load (P) = 10 kN diameter (d) = 40 mm E = 200 GPa…

Q: A steel bar is initially 250 mm in length with a square cross-section of 50 50 mm. The modulus of…

A: load applied along the length will cause longitudinal stress and strain longitudinal stress will…

Q: The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile…

A:

Q: A steel rod with a cross-sectional area of 150 mm² is stretched between two fixed points. The…

A:

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.