A tensile stress is applied along the long axis of a cylindrical brass rod thathas a diameter of 10 mm. Given the Poisson’s ratio for brass is 0.35,determine the magnitude of the load required to produce a 2.5 x 10-3 mmchange in diameter if the deformation is entirely elastic. Take the Young’sModulus (E) for brass as 10.1x104 MPa.

A tensile stress is applied along the long axis of a cylindrical brass rod thathas a diameter of 10 mm. Given the Poisson’s ratio for brass is 0.35,determine the magnitude of the load required to produce a 2.5 x 10-3 mmchange in diameter if the deformation is entirely elastic. Take the Young’sModulus (E) for brass as 10.1x104 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A part made of Aluminum 6061-T6 has a yield strength = 400 MPa. For each stress state below, draw all 3 Mohr's circles, find the principal stresses, and calculate the safety factor against yield using both the distortion-energy (von Mises) and maximum shear stress (Tresca) criterions. (If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels. Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical results A 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications?
i need the answer quickly
This question is from the subject Theory of Elasticity
The cable of hoist has a cross sectional of 80mm2.The hoist is used to lift a crate weighining 500 kg.The free length of of the cable is 30 m.Assume all deformation is elastic. (a) what is the stress on the cable. (b) How much will the cable extend if it is made from steel(E-200 Gpa)? (c) How much will the cable extend if it is made from polypropylene(E-1.2 Gpa)?
Give ONLY the correct answers with their units A. Calculate the axial deformation of a steel rod 20 cm long, 10 cm diameter. If an axial loading 300 MPa is applied at the end. B. If the cross-sectional is square with t=10 mm, is the deformation will be higher or lower. (use E=200 GPa) Y
At the proportional limit, a 16 mm thick x 69 mm wide bar elongates 6.2 mm under an axial load of 485 kN. The bar is 1.5 m long. If Poisson's ratio is 0.32 for the material, determine the modulus of elasticity (in GPa). Note: Do not include units in your answer. Answer:
Answer the attach file
As shown in the figure, when the temperature was 24 ° C, a 0.5 mm gap was left. Determine the approximate value (° C) of the required temperature so that the normal stress in the aluminum bar is 75 MPa.
A bar of 12 mm diameter gets stretched by 3mm under a steady load of 8000 N. What stress would be produced in the bar by a weight of 800 N which falls through 8 cm before commencing the stretching of the bar which is initially unstressed. Take E= 2 × 105 N/mm2
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
A tensile force. of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter decreases to 0.01998 m and the length increases to 2.01 m. The true stress on that rod is?
Need ASAP solution please