A 35 kN axial load is applied to a metal bar with a rectangular cross-section, 28mm wide by 10mm thick. While the load is applied, the bar elongates 3.0 mm. The modulus of elasticity and the Poisson's ratio are 100 GPa and 0.35, respectively. Assuming that the bar is still behaving elastically, how long is the original length of the bar in meters? Round off answers to the nearest tenths

A 35 kN axial load is applied to a metal bar with a rectangular cross-section, 28mm wide by 10mm thick. While the load is applied, the bar elongates 3.0 mm. The modulus of elasticity and the Poisson's ratio are 100 GPa and 0.35, respectively. Assuming that the bar is still behaving elastically, how long is the original length of the bar in meters? Round off answers to the nearest tenths

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the proportional limit, a 16 mm thick x 69 mm wide bar elongates 6.2 mm under an axial load of 485 kN. The bar is 1.5 m long. If Poisson's ratio is 0.32 for the material, determine the modulus of elasticity (in GPa). Note: Do not include units in your answer. Answer:
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.22 cm & the external diameter of 23.4 mm is subjected to an elastic tensile load of 228 kN. Take the elastic modulus of the aluminum specimen as 71 GPa and the initial length of the hollow cylinder as 187 mm. Solution: i) Cross-sectional Area (in mm2) = ii) Stress-induced (in N/mm2) = iii) Strain-induced (at least 3 decimal places accuracy)= iv) Elongation (in mm) =
1 J A cylindrical specimen of steel having a diameter of 14.36 mm and length of 209 mm is deformed elastically in tension with a force of 58.9 kN. Suppose that the Poisson's ratio (v) is 0.3, determine The change in diameter of the specimen? (E of steel = 207 GPa)
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
A piece of steel rebar is tested in tension to determine its mechanical properties. The length of the sample is 87.3 mm and the cross-sectional area is 52.1 mm². When stretched by 37.2 mm, the force measured is 14,884 N. At this point, the graph is non-linear, but no clear neck is visible. If the Poisson's ratio of the material is 0.281, calculate the cross-sectional area (mm²) at this point.
A steel [E = 200 GPa] rod with a circular cross section is 5 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 55 kN without exceeding an allowable stress of 180 MPa. State your answer in mm without including the units, and correct to two decimal places. Answer:
An engineer determines that a 32 cm long rod of 1020 grade steel will be subjected to a tension of 40 kN. The following two design requirements must be met: the stress must remain below 120 MPa, and the rod must stretch less than 0.135 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. (Round up to the nearest millimeter when reporting your answer.) mm
A steel column is a cylinder 6.8 m long and 0.35 m in diameter. What is the change in length of the column when it experiences a tensile stress resulting from the application of a 3600 N force? The elastic modulus for steel is 20 × 1010 Nm2/kg2. ΔL = m
5. Consider a cylindrical specimen of a steel alloy (Figure 6.22) 10 mm in diameter and 75 mm long that is pulled in tension. Determine its elongation when a load of 20,000 N is applied. Stress (MPa) 600 500 400 300 200 100 0 0.00 0.04 Stress (MPa) 500 400 300 200 100 0.000 0.002 0.004 0.006 0.08 Strain Strain 0.12 0.16 0.20 Figure 6.22 Tensile stress-strain behavior for a steel alloy.
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L
A specimen of copper having a rectangular cross section of 15.2mm x 19.1mm is pulled with a force of 44.5kN. Calculate the stress in MPa. Provide your answer to 2 decimal places. Answer: 0 0 Vũ Vũ (DE) + TI a W
1.2 Figure 1 show a compound bar made of the aluminum alloy with three different cross-sectional. The bar is subject to a tensile load of 40KN. Take E = 69 GPa, Determine the stress in each section and the total elongation of the bar 30 mm 40 mm 50 mm 40 kN 40 kN 0= 20 mm 0= 15 mm 0 = 10 mm