A member of a 3D truss is located between the origin of rectangular coordinates and point P (1,1,0.5) m, as shown in Figure P3.1. If the member remains straight and end P experiences small displacements, u=3 mm, v = 2 mm, and w=-1.5 mm, find the average extensional strain of the member.

A member of a 3D truss is located between the origin of rectangular coordinates and point P (1,1,0.5) m, as shown in Figure P3.1. If the member remains straight and end P experiences small displacements, u=3 mm, v = 2 mm, and w=-1.5 mm, find the average extensional strain of the member.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can you please help me with all parts of the question? Thank you
A -A =660 mm 2m Cap plate * Ac =860 mm 3m
The figure below shows a cable supporting a beam. In addition there is a vertical force acting on the right end of the beam. L Calculate the normal force N(x), the shear force V (x), the moment M(x) as a function of the parameters L and f. (Partial Answer: N(x) = 2f for 0
2.6 The truss ABC shown in the figure supports a horizontal load P₁ = 9 kN and a vertical load P₂ = 18 kN. Both bars have cross-sectional area A = 1,290 mm² and are made of steel with E= 210 GPa. a) Determine the strain energy U₁ of the truss when the load P₁ acts alone (P₂ = 0). b) Determine the strain energy U₂ when the load P2 acts alone (P₁ = 0). c) Determine the strain energy U when both loads act simultaneously. 813 mm 1524 mm P₁ = 9 kN P₂ = 18 kN
i need the answer quickly
If Young's modulus of some material is 150 GPa and shear modulus is 50 GPa, find the poisson's ratio of that material.
5
The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150x10° N/m². The cross sectional area of each member is 0.01 m?. Forces P, and P2 are acting as shown, Wall (a) (b) 40% (c)/30 P' P= 2kN 4m FIGURE Q2 a. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by performing complete calculations to justify your recommendation. b. After the client approved your recommendation in (a), it was found that the displacements occurred at node 1 is still high. As a result, you are required to modify the truss design in order to reduce the displacement at node 1 by minimum 15% on a condition that modules of elasticity, and the force remain unchanged. Justify your recommendation. Las digit in Student ID O to 3 4 to 6 7 to 9 30° 36° 40° PI 5 kN 7 kN 8 kN
Figure Q4(a) shows the stress-strain curves of material A and material B. A circular rod of material A (diameter 3 cm, length 10 cm) is bonded to a circular rod of material B (diameter 4 cm, length 20 cm) as shown in Figure Q4(b). a) Based on the stress-strain curves shown determine the yield stress (σy) and the elastic modulus (E) of material A and material B.b) Assuming that the bond is rigid, determine the force P required to stretch the composite rod by 0.3 mm?c) Assuming a Poisson’s ratio value of 0.33, determine the change in diameter of the rod made from material B for the same P as determined in part (b).
A thin steel wire with a uniform cross section is bent as in the figure. Find the position of the center of gravity of the object formed. (second image is an example of a solution to another problem)
A uniform stone slab weighs 400 lb and is suspended by 3 cables and subjected to a downward vertical load as shown in the figure and parameter table. A B F parameter L1 L2 L3 value units 2 ft 4 ft 3 ft F 150 lb The tension in cable A is 200 * lb The tension in cable Bis 35.7 X lb The tension in cable C'is 314 X lb