Problem 5:An experiment was set up according to Figure 5 with the followingL=12 inchesLB1 10 inchesLB29 inchesw1.0 inchest = 0.25 inchesP = 5 lbsWith the load applied, the following strains were recorded:Longitudinal gage = 471 us; transverse gage = -146 μs.Determine the elastic modulus and Poisson's ratio of the beam material. What material is it? LLB1LB2Figure 5: Both strain gages on top,gages mounted a different momentarm distance from loadW

Write the given data. L=12 inLB1=10 inLB2=9 inw=1 int=0.25 inP=5 lbsLongitudinal strain,…

Problem 5: An experiment was set up according to Figure 5 with the followings L = 12 inches LB110 inches LB2 = 9 inches w 1.0 inches t = 0.25 inches P = 5 lbs With the load applied, the following strains were recorded: ● ● Longitudinal gage = 471 ue; transverse gage = -146 με. Determine the elastic modulus and Poisson's ratio of the beam material. What material is it?

Problem 5: An experiment was set up according to Figure 5 with the followings L = 12 inches LB110 inches LB2 = 9 inches w 1.0 inches t = 0.25 inches P = 5 lbs With the load applied, the following strains were recorded: ● ● Longitudinal gage = 471 ue; transverse gage = -146 με. Determine the elastic modulus and Poisson's ratio of the beam material. What material is it?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two rods support the rigid bar ABC as shown in the figure. A downwards load P of 50 kN is applied at A. Rod BD has the following properties: L = 600mm, E = 73 GPa, and A = 1,250 mm². Rod CE has the following properties: L = 400mm, E = 200 GPa and A = 750 mm2. Indicate negative if under compression or if the member contracteri D 200 mm Εἴ 400 mm B 600 mm 300 mm-
The stress-strain diagram for polyethylene, which is used to sheath coaxial cables, is determined from testing a specimen that has a gage length of 11 in. A load P on the specimen develops a strain of € = 0.024 in. /in. (Figure 1) Figure σ (ksi) 5 4 3 2 1 O = 3,7 e O 0.008 0.016 0.024 0.032 0.040 0.048 0.004 1 of 1 P € (in./in.) Part A Determine the approximate length of the specimen, measured between the gage points, when the load is removed. Assume the specimen recovers elastically. Express your answer in inches to four significant figures. 15] ΑΣΦ | 11 | vec L = Submit Provide Feedback Request Answer www ? Review in. Next >
Must answer all the question. Dont attempt it partially. Otherwise dont attempt.
Hi, I need help with this question.
Two [0°, 45°, 90°] strain gauge rosettes are placed along the neutral axis of a 4-point bent beam as shown in the figure below. What will the strain reading in each of the 6 gauges be? P L/3 L/3 -45° 45 L/4 L/2 L NA h
6. State your answers to the following questions.Strain Gauge represents the deformation of a material through a change in resistance. If so, explain how temperature will affect the strain gauge in the experimental environment.①:In this experiment, the Strain Gauge measures the strain in micro units. Explain one possible error factor when applying a load by hanging a weight on the material with the strain gauge attached. (Hint: It is easy to shake by hanging the weight using a thread)①:
a=2 b=5
A small aluminum alloy [E = 75 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b = 21 mm, d= 32 mm, and t = 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 7 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P P ЗР C Strain gage- d E H b Answer: P = i N /2
If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal BD. C 2 mm 4 mm 15 mm A 15 mm Select one: O 0.0382 O 0.0853 O 0.0607 A O 0.0793 O 0.1281
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.4 lb/in.³ is the specific weight of the material, y = 3.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 19 in. is the length of the bar, and E= 24000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar. Part 1 Calculate the change in length of the bar due to its own weight. Answer: d = i x10-6 in.
5- B) What do you mean by strain? A strain gauge has a resistance of 157.4 ohms and a gauge factor of 2.7. Find the change in resistance of the gauge for a strain of 0.0017.
i need the answer quickly