A long, flat steel bar 6 in. wide and 3/8 in. thick has a circular hole 2 in. in diameter, centrally located. The allowable tensile stress for the steel is 22,000 psi. Calculate the stress concentration factor for this case: Calculation your answer to 2 decimal place. 2 6" "DIAM.

Q: If in a tensile loading application, the factor of safety for one member is set as FS = 2.2 based on…

A: Given data: FS=2.2σfail=614  MPa Need to determine the allowable stress for member σallow.

Q: Determine average normal stress. Express your answer in pounds per squared inch to three significant…

A: Note: As per Expert Guidelines we are supposed to answer only the first three parts of the given…

Q: 1. Calculate the stress developed (in Pa) for the following structural members that are each…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: A 2.25 kN m torque is applied to the solid cylinder made up of a hollow cylinder and an inner core…

A:

Q: The bar shown below has a constant width of 41 mm and a thickness of 13 mm. The maximum average…

A: The maximum force in the section CD considering the right portion is The maximum force in the…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs…

A:

Q: The bar shown below has a constant width of 41 mm and a thickness of 16 mm. The maximum average…

A:

Q: 34. Stress is given by the following formula: (choose correct sentences) a. 8 = 4 b. 8 == c. 8=Ex=…

A: Find  Stress is defined as. Types of Cast Iron

Q: 3. From problem 2 HW2. Determine the safety factor if the pipe is made from cast iron (BRITTLE).…

A:

Q: A 2-in.-diameter round steel rod 10 ft long is subjected toa tensile force of 60 kips. How much will…

A: Given Data⇒Diameter of round steeld=2 inLength of round steelL=10 ft=120 inTensile ForceF=60…

Q: .A 3 inches diameter solid shaft is desired to replace a hollow shaft in which the weight of hollow…

A:

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an inner diameter of 18 mm…

A: Part A) The outer diameter of the tube is do = 24 mm = 0.024 mThe inner diameter of the tube is di =…

Q: Calculate the wall thickness required for a thin-walled cylindrical pressure vessel which must…

A: Circumferential stress: A cylinder stress is a stress distribution with rotational symmetry in…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

A:

Q: For the stress element below, when a = 6, b = 6, and c= 8, the principal stress 0₁ is: your answer…

A: Given Data: The value of σx = - 6 Mpa The value of σy = + 6 Mpa The value of τxy = + 8 Mpa Sign…

Q: 1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to…

A: Given:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.