A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 47 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft O 2.93 kips 4.54 kips O4.84 kips O 3.57 kips O 5.62 kips B 3 ft P 8 ft 1.5 ft

A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 x 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 x 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 47 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft O 2.93 kips 4.54 kips O4.84 kips O 3.57 kips O 5.62 kips B 3 ft P 8 ft 1.5 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN 400 mm 600 mm A B C 30 mm 50 KN 50 mm
i need the answer quickly
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises by 20∘C after a load W = 110 kN is applied. Use the following properties in the table.
pls help me. thank u refer to the picture attached below.
Step by step solution *
5. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free, what is the largest load P that can be applied without exceeding stresses of 150 MPa in the steel rod and 70 MPa in the bronze rod? -2 m- -1.5 m- 1.5 m- Bronze A = 300 mm2 E = 83 GPa L=2 m Steel A = 900 mm2 E = 200 GPa L = 1.5 m
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.21 in.? and an elastic modulus of 2350 ksi. Bar (2) has a cross-sectional area of 1.032 in.? and an elastic modulus of 4100 ksi. Assume L1=20 in., L2=49 in., Q=7.1 kips, P=2.9 kips, and R=12.9 kips. Determine the horizontal deflection of end C relative to end A. P (1) (2) C В L1 L2 Answer: uc/A in. %3D