A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in a cyclical fashion as the mechanism runs. It has been decided to use AISI 1040 cold-drawn steel. Complete the design of the link, specifying a suitable cross-sectional shape and dimensions. 5. Specify the required length of no. 60 chain to mount on sprockets having 15 and 50 teeth with a center distance of no more than 36 in.

Q: The transmission shaft shown in the figure below is used by two V-belt pulleys for movement…

A:

Q: Numerical 4. DESIGN OF BELT CONVEYOR SYSTEM WITH THE FOLLOWING SPECIFICATION Material to be carried…

A:

Q: A helical compression spring is to be cycled between 150 lbf and 300 lbf with a 1-in stroke. The…

A: (Bartleby policy): Since you have posted a question with multiple sub-parts, we will solve the first…

Q: = 8 kN, T12 = 2 kN, T

A:

Q: A deep groove ball bearing (with normal clearance) is subject to an axial load of 17 kN and a radial…

A:

Q: Find the number of bolts M8*1 which made from SAE Grade 4 steel that should be used to provide a…

A:

Q: A self-aligning ball bearing used in the car manufacturing industry has a basic dynamic load rating…

A:

Q: (c) The type of pressure plate chosen as a result of the calculation in part (b) of this question…

A: A clutch is a device that allows two elements with a common axis of rotation to connect and detach…

Q: A chain sprocket system is designed to drive a shaft. Assume the following conditions: Use SAE1018…

A:

Q: 5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for…

A:

Q: The wire diameter Mean coil diameter. Number of active coils Total number of coils Free length of…

A:

Q: The following data relate to a screw jack: Pitch of the threaded screw = 8 mm Diameter of the…

A:

Q: solve/ show solution for given answer equations  kb = (Ab*Eb)/ g and kc = (Ac*Ec) / g   g- estimated…

A: I have attached the image below Explanation:

Q: Figure 1 is a schematic drawing of a countershaft that supports two V-belt pulleys. For each pulley,…

A: Given data, For pulley A Tension in tight side, T1 = 103 N Tension in loose side, T2 = 0.15T1…

Q: The cantilever bracket is bolted to a column with three M12x1.75 ISO 5.8 bolts. The bracket is made…

A: The ability of a system's structural capability to be viable beyond its projected or actual loads is…

Q: repeat problem 8-19 with the bottom aluminum plate replaced by one that is 20 mm thick.

A: The total grip length is the sum of the thicknesses of the plates being clamped together. In this…

Q: The two lever assembly shown below is subject to a static load F = 8250 lb. (a) identical links BD…

A: Given:

Q: Required information A helical coil compression spring is needed for food service machinery. The…

A: helical coilExplanation:Step 1:Step 2:Step 3:Step 4:

Q: esign a clamp coupling to transmit ‘35’ kW at ‘120’ r.p.m. The allowable shear stress for the shaft…

A: GivenPower P=35kWN=120rpmτshaft=τkey=50MPanumber of bolts n=6The permissible tensile stress for the…

Q: Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered…

A: given subjected load, Pmin=416Nsubjected load, Pmax=950Nspring index,C=Dd=6.7factor of safety…

Q: A self-aligning ball bearing used in the car manufacturing industry has a basic dynamic load rating…

A: Given data dynamic load rating of (C) = 48899 N life of the bearing  (L) = 2303 millions of…

Q: A link in a mechanism is to be subjected to a tensile force that varies from 3500 to 500 N in a…

A: Soln :- In a given problem we have a link that mechanism is subjected tesnile force which is able to…

Q: 1. A full journal bearing of 150 mm diameter supports a load of 40 kN. The speed of the journal is…

A:

Q: Find the number of bolts M8*1 which made from SAE Grade 4 steel that should be used to provide a…

A:

Q: 1. For the spring system given in Figure 1; Number the elements and nodes; i. ii. Assemble the…

A:

Q: ad acting on

A: GIVEN:N=1450RPML10h=8000P=5000N

Q: Design the elliptical cross-section of a belt pulley arm near the hub for the following…

A: We have to design the cross section of belt pulley .

Q: The pedal system shown in the figure is exerted by both an up and down mechanism. These forces are…

A: Given: The maximum load, Fmax = 350*89/10 = 3115 N The minimum load, Fmin = - 150*89/10 = - 1335 N…

Q: Part 1 is as follows: al Diameter (mm) Tolerance (mт- 6 - 7.5 + 0.045 8 –10 + 0.050 a diameter wire…

A: To Find :  The mean and standard deviation of the population of torsional shear stress  Given : The…

Q: 1 1. FIMD RXAS AT A D 2. ou Pids oF POLLETS Bx By C- C. C. ALE OF RESUTAT AT B,C &A

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: The adjustable height caster is designed to carry 2000 N and operate on the floor that may not be…

A: Based on the information you provided and the image of the adjustable height caster, here's how to…

Q: be made of tempered wire. Since the material is to be subje and fatigue must be considered a low…

A:

Q: 1. A full journal bearing of 150 mm diameter supports a load of 40 kN. The speed of the journal is…

A: Designing the journal bearing.

Q: Compute the contact stress number for the gear fain pair driven directly by an electrical motor. The…

A:

Q: RB&W11 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4…

A: To findthe torque is necessary to establish the desired preload.The turn of the nut.Givenpreload,…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.