A large tank open to the atmosphere is filled with water to a height of 5 m form the outlet tap. A tap very near to the bottom of the tank is now opened and water flows from the smooth and rounded outlet. Determine the water velocity at the outlet assuming there are no friction losses in the system. If the diameter of the tank is 2 m, and the diameter of the outlet is 1 cm, how long it takes to empty the tank from the outlet.

A large tank open to the atmosphere is filled with water to a height of 5 m form the outlet tap. A tap very near to the bottom of the tank is now opened and water flows from the smooth and rounded outlet. Determine the water velocity at the outlet assuming there are no friction losses in the system. If the diameter of the tank is 2 m, and the diameter of the outlet is 1 cm, how long it takes to empty the tank from the outlet.

Name: A large tank open to the atmosphere is filled with water to a height
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A large tank open to the atmosphere is filled with water to a height of 5 m form theoutlet tap. A tap very near to the bottom of the tank is now opened and water flowsfrom the smooth and rounded outlet. Determine the water velocity at the outletassu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A woman is draining her fish tank by siphoning the water into an outdoor drain as shown in the…

A: The area of the base of the rectangular tank is A and the height is hTherefore, the volume of the…

Q: To have a complete understanding of the hydraulic system, it is required to determine the efficiency…

A: Given Data: The discharge through the nozzle is Q=100 L/s. The value of Cv =0.97. The tangential…

Q: A pump is to deliver water at a head of 40 m, the water temperature being 38oC and barometric…

Q: Q7) Air is flowing through a pipe and a mercury manometer is attached with this pipe. If the…

Q: A 9.0-cm diameter pipe contains water with a mean flow velocity of 2.0 m/s. The pipe has a 90-degree…

Q: Water is flowing through a pipe of 0.60-meter diameter and 2-kilometer length. If the average…

A: As the values are given .. We know that head loss due to friction(hl)=flv2/2gD

Q: A tap discharges water evenly in a jet at a velocity of 2.6 m/s at the tap outlet, the diameter of…

Q: Once it has been started by sufficient suction, the siphon in Fig. 8-29 will run continuously as…

A: a)Bernoulli equation between 1 and 2, P1+12ρwv12+0=P2+12ρwv22-rwH12ρwv22=rwH…

Q: The water flows from the pipe shown in the figure with a flow rate of 0.025 m3 / s and emerges into…

Q: A U-tube acts like a water siphon. The elbow in the tube is 1 m above the water surface, the tube…

Q: onsider the hydropower schematic shown below with a lake of 70m elevation above a turbine house.…

Q: Q4: Two centrifugal pumps (A) and (B) are to be used to pump water for vertical distance equal to…

Q: As shown in the figure, water enters and leaves a U-shaped piece of pipe in the horizontal plane.…

A: Density It is the property of fluid which is ratio of mass and volume of fluid. Continuity…

Q: Calculate (a) the mass flow rate through the system and (b) the force that is required to hold the…

A: To calculate the volume flow rate of water through the pipe, we must apply the Bernoulli's theorem…

Topic Video

Question

A large tank open to the atmosphere is filled with water to a height of 5 m form the
outlet tap. A tap very near to the bottom of the tank is now opened and water flows
from the smooth and rounded outlet. Determine the water velocity at the outlet
assuming there are no friction losses in the system. If the diameter of the tank is 2 m,
and the diameter of the outlet is 1 cm, how long it takes to empty the tank from the
outlet.
5 m
Water

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

help me answer, thank you.
Gardeners are holding a nozzle at the end of a hose to wash way mud from landscaping. The nozzle exit has a diameter of 10cm and the water is flowing at a rate of 12 m3/min. In this situation, what is the average water exit velocity and what is the horizontal resistance force required to hold the nozzle? Any help would be great
kg Water (p = 1000- -) flows through the elbow below. The diameter of both the inlet and outlet is 1.1 cm, and the velocity through the nozzle is V =4.5 m/s. The outlet m³ has an angle of 0 =15 degrees. The water is at a pressure of 29 kPa (gauge). Find the magnitude of the force on the elbow. 0 V
Consider water flowing through a water hose of length of 100 ft, diameter of 3/8 inch, and average surface roughness 5-105 ft. The gage pressure at the hose inlet is 40 psi. The hose contains a ball valve which controls the flow rate. Calculate the mass flow rate of water through the hose with the ball valve completely open and with ball valve 2/3 closed. Hint: Determining the friction factor requires an iterative approach - start the iterations by assuming that the friction factor is equal to 0.01 and perform at least 3 iterations.
In the figure below, the tank containing the water is very large and open to the air, and the pipe through which the water drains is very small. The pipe is not open to the air and the water can be treated as an ideal fluid. Find the speed at which the water is traveling in the pipe.
An elbow deflects water upward and discharges it to the atmosphere at a specific rate. Determine the gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place. (gage pressure at the outlet is zero)
The turbine at C draws a power P kW. If the intake B has a diameter of de mm. The pressure dg(mm) dĄ(mm) at the intake B is Ps kPa and the velocity of the water (density = 1kg/L) at that point is v (m/s). The frictional losses between A and B are At neglected, and the exit A has a diameter of da B1 mm. Consider the data in the table to M = last two digits of your student ID P (kW) = 0.5M + 68.5 da(mm) = M + 150 dp (mm) %3D М + 400 PB (kPa) = M + 380 v (m/s) = 0.1M + 4 a- Calculate the velocity at the exit A b- Calculate the discharge at the exit A c- Calculate the turbine head d- Calculate the pressure at A m=13
A storm drain has a maximum capacity of 120 L/min. During heavy rains, an influx of 240 L/min approaches the drain. Assuming the drain is cylindrical, by how much would the drain radius need to be increased to handle the heavier rainfall? Assume the water travels at the same linear speed in both drains. The answer is 1.4. Please explain why A 16 times greater B 42 times greater C 2 times greater D 1.4 times greater
Question Water enters the horizontal circular nozzle with the inlet diameter of 5 in. At the inlet section, fluid has uniformly distributed velocity of 20 ft/s and pressure of 85 psi. The water exits from the nozzle into the atmosphere at the outlet section where the uniformly distributed velocity is 100 ft/s. Determine the axial component of the anchoring force required to hold the contraction in place. Answer The axial component of the anchoring force required to hold the contraction in place is lbf.
Determine the downstream pressure P2, and estimate the error that would have occurred if Bernoulli's equation had been used, if the horizontal pipe has an abrupt expansion from D1 = 8 cm to D2 = 16 cm. The water velocity in the smaller section is 10 m/s and the flow is turbulent. The pressure in the smaller section is P1 = 300 kPa. Taking the kinetic energy correction factor to be 1.06 at both the inlet and the outlet. D = 8 cm Water D2 = 16 cm 10 m/s 300 kPa
The pump shown in the figure below produces a steady flow of 12 gal/s through the nozzle. Determine the nozzle exit diameter, D2, if the exit velocity is to be V₂ = 109 ft/s. D₂ = Pump i Section (1) Section (2) V₂ in
a hemispherical bowl of a radius 10m is filled with water. There is a small hole of radius 10cm at the bottom of the convex surface. assume that the velocity of efflux of the water when the water level is at height h(m) is v=0.14 sqrt 2gh. Determine the time in hours taken for the bowl to empty.