Determine the downstream pressure P2, and estimate the error that would have occurred if Bernoulli's equation had been used, if the horizontal pipe has an abrupt expansion from D1 = 8 cm to D2 = 16 cm. The water velocity in the smaller section is 10 m/s and the flow is turbulent. The pressure in the smaller section is P1 = 300 kPa. Taking the kinetic energy correction factor to be 1.06 at both the inlet and the outlet. D =8 cm Water D2 = 16 cm 10 m/s 300 kPa

Determine the downstream pressure P2, and estimate the error that would have occurred if Bernoulli's equation had been used, if the horizontal pipe has an abrupt expansion from D1 = 8 cm to D2 = 16 cm. The water velocity in the smaller section is 10 m/s and the flow is turbulent. The pressure in the smaller section is P1 = 300 kPa. Taking the kinetic energy correction factor to be 1.06 at both the inlet and the outlet. D =8 cm Water D2 = 16 cm 10 m/s 300 kPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.38 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.74 m.
could you please help me calculate theheigth in metres of the fluid at time t= 100s
Water flows steadily through the elbow, placed horizontally on the surface shown in figure. Determine the force kN needed to hold the elbow in place. (NOTE: Pwater = 1000 kg/m) -5m 45 cm -30kPa P-250 Pa 25 cm A-170 AP K-15 ms 20 cm
Question 3 Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of 2 m/s. The length of the pipe is 40 m. A pump is used to maintain the flow from one reservoir to another reservoir as shown. The following data are available: KL elbow = 1.5, Kentrance = 0.5, Kexit = 1.0. Elbow Pump Elbow Figure Q1 Note that the entrance and exit are at the same elevation. The free surfaces of the reservoirs are also at the same elevation. (a) Calculate the total head losses in the pipe.
Consider a pipe that has a diameter D = 18 inches and a length L = 2,000 feet. The pipe delivers water from an upper reservoir to a lower reservoir. The water surface elevation of the upper reservoir is 50 feet and the water surface elevation of the lower reservoir is 0 feet. The water temperature is 50°F. Use the Darcy- Weisbach equation with a friction factor f = 0.0125 to evaluate the friction head loss hfric. Assume that minor losses are equivalent to 15% of the friction head losses (i.e., hminar = 0.15 x hfic So total head loss hi total = hfic + hminar = 1.15 x hfnc). a) Determine the flow in cubic feet per second (cfs). b) Determine the friction head loss hfñic in feet. c) Determine the minor head loss hminar in feet. d) Does hfric + hminer = 50 feet? If yes, GREAT! If not, find your mistake.
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
The properties of the air in the inlet section with A1 = 0.2562 m2 in a converging-diverging channel are given as U1 = 256,2 m/s, T1 = 362 K, P1 = 136,2 kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Solution please.
Water at 15 degrees Celsius is flowing through a 2-in ID smooth pipe. The friction loss for a 100-ft section of the pipe amounts to 4.8 lbf/lbm. Determine the velocity of the flow.
Water flows from a large, pressurized tank through a 6 in diameter pipe and rises 20 ft above the nozzle (see figure). Determine the pressure in the tank, pt, and the volumetric flowrate. Assume the flow is steady-state and frictionless, and the kinetic correction coefficient a 1. Patm Pt 20 ft 25 ft 10 ft
Oil at 60 degrees celsius and 140 bars is flowing through a pressure relief valve at 0.01 m3/s. What is the downstream temperature? Show your work.
In the diesel oil transfer facility (ρ rel = 0.85), from the storage tank to the consumption tank, we want to install a pump to circulate a flow of 45 lt / s. The 400m long pipe is cast 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 3.8 bar of manometric pressure. Determine the drive power of the pump in kW if its performance is 68%. Additional data, load loss factors: 1. Check valve Kr = 1.5 2. Gate valve open Kv = 0.21 3. Commercial elbow of mean radius Kc = 0.75, for each elbow 4. Storage tank outlet sharp angles Ks = 0.5 5. Entrance to consumption tank Ke = 1 6. Pipe friction factor f = 0.025