A jet of velocity of 20 m/s strikes a flat plate inclined at 30° with the axis of the jet. If the cross sectional area of the jet is 20 cm2, find the force exerted by the jet on the plate. Also calculate the components of the force in the direction normal to the jet. Find also the ratio in which the discharge gets divided after striking the plate.

A jet of velocity of 20 m/s strikes a flat plate inclined at 30° with the axis of the jet. If the cross sectional area of the jet is 20 cm2, find the force exerted by the jet on the plate. Also calculate the components of the force in the direction normal to the jet. Find also the ratio in which the discharge gets divided after striking the plate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Consider a water jet having a diameter of D = 1 cm and a flow of Q = 1 L/s. The jet is deflected by a fixed plate which is inclined at an angle of 50° from horizontal. a) Determine the velocity vx in the x-direction in m/s. b) Determine the velocity vy in the y-direction in m/s. c) Determine the resultant force Fx on the plate in the x-direction in N. d) Determine the resultant force Fy on the plate in the y-direction in N. e) Determine the combined resultant force F on the plate in N. 1 L/s 50° V = 6 m/s
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
The block slides at a constant speed on a surface with friction. In each case, the water jet has velocity 50 m/s and cross-sectional area 5 cm2, and the block has velocity 25 m/s. In case (a), the jet is deflected to an angle of 60° from horizontal relative to the block, as shown. In case (b), the jet is deflected 180°. Calculate the friction force in each case. Apply both a moving Reference Frame (RF) and a fixed RF. Use the VSM. Check that both RFs give the same friction force for a given case. (We would not expect the two cases to have the same friction force!) Density of water is 1000 kg/m3. All jets are open to the atmosphere. case (a) 60° case (b)
calculate the value of the force exerted by the water above the window of the dam. Be sure to explain why if the pressure varies from the surface of the water, the lower limit for the integral is taken from depth "a" and not from zero? (it is convenient that you make diagrams to support your answer).
Determine the horizontal and vertical components of the total force acting on the cylinder per meter of its length.
From the figure below, determine the reaction force at point O. DE 0.5 m 0.5 m 0.4 m F = 300 N B A 0.3 m 0.2 m 0.1 m y
The masses of the blocks are mA = 30 kg and mB = 70 kg. Between all of the contacting surfaces the coefficient of static friction is O0.1. 1. What is the largest force F that can be applied without causing the blocks to slip? 2. What is the reaction between the two blocks? 3. What is the reaction between the floor and block B 30 F 4. 20°
A plate 0.025 mm distant from a fixed plate, moves at 60 cm/s and requires a force of 2N/m² to maintain this speed. Determine the fluid viscosity between the plates.
statics of rigid bodies
A 200-lb block is on top of a 300-lb block and both blocks are tied to a pulleya pulley that is attached to the wall, as shown in the figure. The coefficient of static friction between thetwo blocks is 0.3 and between the 300 lb block and the floor is 0.4. The coefficient of dynamic frictionbetween all surfaces is 0.25. Disregard the friction at the pulley.Determine the minimum force that must be applied to the 300 lb block in order for it to initiatemotion (imminent motion).