Consider the hemispherical gate attached to a cylindrical buoy as shown in the figure. The thickness of and weight of the cable connecting the buoy and the gate are negligible. Which of the following is the volume above the hemispherical gate that is needed in the calculation of the vertical component of the resultant hydrostatic force acting on it? =? Select one: O a. cylinder up to the liquid surface O b. cylinder up to the liquid surface minus the hemisphere O c. cylinder up to the bottom surface of the buoy O d. cylinder up to the bottom surface of the buoy minus the hemisphere

Consider the hemispherical gate attached to a cylindrical buoy as shown in the figure. The thickness of and weight of the cable connecting the buoy and the gate are negligible. Which of the following is the volume above the hemispherical gate that is needed in the calculation of the vertical component of the resultant hydrostatic force acting on it? =? Select one: O a. cylinder up to the liquid surface O b. cylinder up to the liquid surface minus the hemisphere O c. cylinder up to the bottom surface of the buoy O d. cylinder up to the bottom surface of the buoy minus the hemisphere

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Can the system in given figure be in static equilibrium in the position shown? The uniform bar AB weighs 500 lb, and the weight of block C is 300 lb. Friction at A is negligible, and the coefficient of static friction is 0.4 at the other two contact surfaces. B C 5 m 30° 50°
4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)
There two parallel discs, one is up and another is down, whose diameters are both d. The thickness of the gap between the two discs is ô. The dynamic viscosity coefficient of the liquid in the gap is µ. The below disc is fixed. The above disc rotated around the axis at the angular velocity o. How much is the torque to make the disc rotate?
pls answer the table also
4. A 10-kg cylinder is suspended by the frictionless and massless spring-pulley system in Figure 4 (the ring that connects the springs has negligible mass). Each spring has a rest (unstretched) length of 1 m. Find the set of spring stiffnesses KAD, KAB, and KAC that keeps this 10-kg cylinder in static equilibrium. KAD 2 m 2 m A KAB KAC 3 m- B C 4 m 3 m Figure 4 A spring-pulley system holding a cylinder in static equilibrium.
At a temperature of 90°C, a steel tire 10-mm thick and 75mm wide that is to be shrunk onto a locomotive driving wheel 1.8-m in diameter just fits over the wheel. Determine the contact pressure between the tire and the wheel after the assembly cools to 20°C. Neglect the deformation of the wheel caused by the pressure of the tire. Assume a=11.7 µ m/ (m ºC) and E=200 x 10° N/m².
From the figure below, determine the reaction force at point O. DE 0.5 m 0.5 m 0.4 m F = 300 N B A 0.3 m 0.2 m 0.1 m y
STRUCTURAL ANALYSIS II
MECHANICS OF DEFORMABLE BODIES WRITE THE COMPLETE SOLUTIONS. UPVOTE WILL BE GIVEN. ANSWER IN 2 DECIMAL PLACES.
A steel tube is 5 millimeters thick and has an outside diameter of 60 millimeters. It is being used as a compression member. If the axial normal stress in the member is only limited to 200 megapascals, determine the maximum load P in kN that the member can support. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and the final answers to 3 decimal places.
For fluid undergoing circular motion, the centripetal force is provided by a pressure difference. Consider a fluid element (density p) at radial distance r, which has thickness dr in the radial direction and surface area dA normal to the radial direction. The pressure difference gives rise to a force on the fluid element equal to (p(r + dr) – p(r))dA. (i) Equating the pressure difference to the centripetal force, find an expression for the radial pressure gradient in terms of p, r, and fluid velocity v. (ii) A fluid is undergoing body rotation in the r-0 plane (cylindrical polar co-ordinates). By considering the gravitational pressure head, show that the shape of a free surface z(r) is parabolic. (iii) Find and sketch a similar expression for the free surface of a fluid vortex produced by a rotating cylindrical spindle (i.e. a solid cylindrical rod) of radius Ro.