A hydraulic ram pump lifts 0.005 m3/s of water to a tank 20 m above the ram through a 80 m long and 6.5 cm diameter delivery pipe. Take Darcy friction coefficient f = 0.01 and neglect frictional loss in the supply pipe. If the supply tank is 3 m above the ram and supplies 0.1 m3/s of water;

A hydraulic ram pump lifts 0.005 m3/s of water to a tank 20 m above the ram through a 80 m long and 6.5 cm diameter delivery pipe. Take Darcy friction coefficient f = 0.01 and neglect frictional loss in the supply pipe. If the supply tank is 3 m above the ram and supplies 0.1 m3/s of water;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A hydroelectric plant has a dam with a gross height of 381 m with respect to the collectors and a…

Q: You wash your roof with a water hose at a height of 8.0 m above the ground. You connect two garden…

A: Given- P1 = Atmospheric pressure = 1.01 x 105 Pa v1 = 6 m/s height from datum 2 to 1 = (h) = 8 m By…

Q: In a pumping system, a smooth pipeline with an inner diameter of 10 cm is used to transfer liquid…

A: The diameter of the pipe, d = 10 cm = 0.1 mThe flow rate, Q = 10 L/s

Q: 2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The…

Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…

Q: A 30-inch diameter steel pipe (ɛ = 0.00020 feet) delivers water from a reservoir into a…

A: Given data, D = Diameter of the pipe = 30 inch D = 2.5 ft ε = Roughness = 0.00020 ft Q = Volume flow…

Q: A reducing elbow is used to deflect and accelerate the flow of water from a horizontal pipe to 30 °…

A: Given: The pipe angle, θ = 30° The mass flow rate, m = 14 kg/s The cross-section area at inlet, A1 =…

Q: A 70 cm diameter centrifugal pump which is dynamically similar to the tested pump tabulated above,…

Q: A hydraulic orchard pruner is driven by an engine with an output of 20 bhp . If the pump has a…

Q: In a hydroelectric power plant as shown in the figure, 100 m3/s of water flows froman elevation of…

A: Given Volumetric flow = 100 m3/s Elevation = 130 m Overall efficiency = 0.8 % To find Electric power…

Q: At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: A thin disc with mass 0.01 kg is kept balanced by a jet of air. The diameter of the jet at the…

A: The mass of the disc is: m= 0.01 kgThe diameter of the jet nozzle is: d=5 mm = 0.005 mThe density of…

Q: Two long pipes in parallel are used to carry water between two reservoirs. The diameter of one pipe…

Q: Flowrate of water through bend pipe (90o ) is 0.21 m3 /s. The pipe diameter at the inlet is 150 mm…

A: Write the given data with suitable variables: Q=0.21 m3/sd1=150 mm=0.15 m1 m1000 mmd2=75 mm=0.075…

Q: A pump sends a substance (sg=1.9) from a tank to a tank placed at a higher level, where the velocity…

A: Given specific gravity Sg = 1.9 velocity at 2 v2 = 1 m/s friction losses hl = 5.8 m efficiency of…

Q: Through a duct air enters a fan at 6.3 m/s and an inlet static pressure 2.5 cm of water less than…

A: Solution is attached below:

Q: Water flows between two reservoirs A & B. The water level in A is 400 m AOD and in B is 385m AOD.…

Q: Water flows through a circular tube with a constant diameter at a constant flow rate. The outlet is…

Q: A pump draws water from a reservoir and delivers it through a pipe 200 mm in diameter, 120m long to…

A: Given; The diameter of pipe, d = 200 mm The length of pipe, L = 120 m The height of tank, h = 20 m…

Q: A drainage hole (assumed to be a smooth edged orifice) is opened at the bottom of a storage tank…

Q: In a hydroelectric power palnt, water flows from an elevation of 400 ft to a turbine, where electric…

Q: Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of…

Q: (1) Water Pump m L To double the outflow of a reservoir, a pump is added as shown in the Figure…

Q: A small centrifugal pump, when tested at N = 2875rpm with water, delivered Q = 252 gpm and H = 42…

Q: The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from…

Q: Large hydroturbines achieve overall efficiencies above 95%, while the best efficiency of large…

A: The reason of large hydro turbines achieve overall efficiencies more than large pumps are given…

Q: A pipeline, 50 cm diameter and 4,500 m long, connects two reservoirs whom constant difference of…

Q: A pump is used to take water out of a large lake and deliver it to a farm to be used for irrigation.…

A: Given data: Q=100 L/sd=150 mm Need to determine the pressure in the suction side.

Q: A 28-in pump is used to deliver water from a lower reservoir to a higher reservoir . The total…

A: Given:d=10 inL=62 ftf=0.022H=365-0.04718Q2

Q: The water level in a tank open to the atmosphere is 20 m above the ground. A hose connected to the…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

B) Calculate the Rankine efficiency, in %, of the ram pump.
56.5
65.9
37.8
O 49.1
42.8
A) Calculate Aubuisson's efficiency, in %, of the ram pump.
37.8
42.8
49.1
O 65.9
O 56.5

A hydraulic ram pump lifts 0.005 m3/s of water to a tank 20 m above the ram through a 80 m long and 6.5
cm diameter delivery pipe. Take Darcy friction coefficient f = 0.01 and neglect frictional loss in the supply
pipe. If the supply tank is 3 m above the ram and supplies 0.1 m3/s of water;

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a hydroelectric plant the difference in elevation between the surfaace of the water at the intake and at the tailrace is 183m (600ft). When the flow is 80 cfs, the friction loss in the penstock is 60 ft and the head utilized by the turbine is 460 ft. The mechanical friction in the turbine is 100hp, and the leakage loss is 3 cfs. Find (a) hydraulic efficiency; (b) volumetric efficiency; (c) power delivered to shaft; (d) brake horse power, (e) mechanical efficiency; (f) over-all efficiency.
700 gpm of water are being discharged by a centrifugal pump 5 ft above the pump inlet. The inlet pressure is 4 inHg above atmospheric and the discharge pressure is 29 psia. If the pump has an 8 in inlet diameter and 4 in discharge diameter.Calculate (a) the pump efficiency (b) the new flowrate and brake horse power if the pump speed is increased from 1600 to 3200 rp,. Assume the pump input is 8 Hp
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST
A thin disc with mass 0.018 kg is kept balanced by a jet of air. The diameter of the jet at the nozzle exit is 5 mm. Find the air jet velocity in m/s. Please note that the only forces involved are the weight of the disc and the force from the air jet (the two are balanced). Use the air density of 1.07 kg/m^3 , g = 9.81 m/s^2 and the correction factor beta of 1
pipe 1=220mm, pipe 2=320mm, pipe 3=420mm
Show Complete Solution
(a) Water flows by gravity from one lake to another as illus- trated; the surface levels of the lakes differ by an eleva- tion of h= 50 ft. If the volumetric flow rate is steady at Q = 80 gallons per minute, what is the associated loss of available energy? (b) A pump is to be installed to pump the water from the lower lake to the upper lake with the same flow rate as above (Q = 80 gpm). If the amount of energy loss is assumed to be the same as in part (a), how much mechanical power must be supplied by the pump? Answer: (a) loss = 1600 ft-lb/slug, (b) Wpump = 2.0 hp
H-W 1 Q1/ Neglecting losses, determine the discharge in Fig. below Oil sp gr 0.75 3 ft 4 in, diam Water Q2/When the pump in Fig. below draws 220 m/h of water at 20°C from the reservoir, the total friction head loss is 5 m. The flow discharges through a nozzle to the atmosphere. Estimate the pump power in kW delivered to the water. D = 5 cm Ve D= 12 cm 2 m Pump 6 m Water Q3/ The horizontal pump in Fig. below discharges 20°C water at 57 m/h. Neglecting losses, what power in kW is delivered to the water by the pump? 120 kPa 400 kPa Pump D =9 cm D2 =3 cm
Water from a reservoir is pumped over a hill through a pipe 3 ft. in diameter, and a pressure of 35 psi is maintained at the summit, where the pipe is 300 ft above the reservoir. The quantity pumped is 55 cfs, and by reason of friction in the pump pipe there is 10 ft of head loss between the reservoir and the summit. What amount of energy must be furnished the water by the pump in kilowatts?
A centrifugal pump operating under steady flow conditions delivers 2112kg/min of water from an initial pressure of 156 kPa to a final pressure of 1224 Pa. The diameter of the inlet pipe to the pump is 20cm and the diameter of the discharge pipe is 8cm. What is the work done?
A hydraulic motor has a displacement of 100 cm3 and operates with a pressure of 105 bars and a speed of 1700 rpm. If the actual flow rate consumed by the motor is 0.0025 m3/s and the actual torque delivered by the motor is 350 Nm. Calculate the overall efficiency of the motor. If the power supply to the motor is now reduced by 25%, what would happen to the overall efficiency of the pump? Support your answer with relevant calculations. You may propose your own scientific assumptions.
I need help on this question: According to the question: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and Darcy friction factor of 0.03, what would be the actual head rise across the pump for a case where the pump outlet pressure is 200 kPa? The difference in height between pump inlet and outlet is 0.25 m, the tank exit is sharp-edged, and the water level in the tank to the tank exit pipe (HWL) is 2 m. Also, consider that the flow velocity inside the tank is negligible. The value of the actual head rise across the pump is = ? b) What would be the pump motor power if the efficiency is 60%? The value of the pump motor power is = ?