The average flow speed in a constant-diameter section of the pipeline is 2.5 m/s. At the inlet, the pressure is 5000 kPa (gage)and the elevation is 100 m; at the outlet, the pressure is 500 kPa (abs) and the elevation is 5 m. The specific weight of theflowing fluid is 10 kN/m3. Patm = 100 kPa. Pipe diameter = 10 cm. Kinetic energy correction factor, a1 = a2 = 1.Find the following:The power carried by fluid into the control volume, (W).Head carried by fluid out the control volume, (m).The head loss in this section of pipeline (m)

Total energy available at entry per unit volume is given by the the bernoulli's equation P₁ +…

Answered: The power carried by fluid into the…

The power carried by fluid into the control volume, (W). Head carried by fluid out the control volume, (m). The head loss in this section of pipeline (m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Data: Hp2,3 = 2 m; A3 = 20 cm²; A₂ = 1 cm²; Hp0,1 = 0.8 m; NB= 74%(pump efficiency) To determine: a) the flow (L/s); b) the area of section (1) (cm³); c) the power supplied by the pump to the fluid.
8.59 Two tanks A and B, of constant cross-sectional area of 10 m² and 2.5 m², respectively, are connected by a 5 cm pipe, 100 m long, with f = 0.03. If the initial difference of water levels is 3 m, how long will it take for 2.5 m³ of water to flow from A to B? Considering entry and exit losses, it can be grossly assumed that the flow velocity, in m/s, through the pipe is 1.75√h, where his in m, taking g = 10 m/sec², also, may take area of pipe as 2 x 10-3 m².
In mechanical fluid
Attached file please thankyou.
Calculate the hourly energy cost for pumping riverwater at 288.706K, from a river to a hilltop, through a 0.458-ft ID pipeline at an average velocity of 8.1818 mi/hr (mph). The pipeline is 0.8523 miles long and discharges into the atmosphere at a level 0.5682 miles above the level of water in the river. The pump is 70 percent efficient and local energy cost is 7 cents per KWH. Assume friction losses inside the pump to be 1.0779 kJ/kg.
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
Q2: By using the General flow equation: Rew d 0.5 (P? - GT;LZ Q = 38.77F D².5 Approve that, for two parallel gas pipelines (1- BCE & 2-BDE ) as shown in the figure below, the equivalent pipe diameter for both pipelines can be determined by the following equation: 1/5 K. 1+ const1 K D, = D1 const1 where A E K2 (D 5 La constl =
In the design of a 500m long water pipeline it is proposed to keep head loss, hf, less than 6m for a flow of 0.50 m's1. The pipeline must also be able to withstand water hammer pressures under rapid valve closure condition at the discharge end. Two types of pipes- PVC and steel - each 50 cm in diameter are available. Which pipe will you recommend? 1. The Darcy friction coefficient, 2, can be estimated from Figure 1. The value of the roughness height for steel pipe is 0.00015m, while the PVC pipe can be considered hydraulically smooth. The thickness of each pipe is 1 cm and the Modulus of Elasticity, E, for steel is 200x10° Nm2 and for PVC is 1.7×10®N%?. The Bulk Modulus of Elasticity, K, for water is 2x10°Nm2. The working pressures for the steel and PVC pipes are 2 MPa and 1 MPa respectively. 0,1 0,09|Laminar flow f IN aica Transition 0,08 Laminar Critica! flow Complete turbulence, rough pipes Zone 20ne 0,05 0.07 0,04 0,06 0,03 0,05 0,02 0,015 Lio 0,04 0,01 0.008 Re, 0,006 0,03 0,004…
With FBD.
sg(water@25degree)=9.78kN/m^3 k=0.42
10. A fluid moves in a steady flow manner between two sections in a flow line. At section 1:Ai-10ft, U1 = 100 fpm, vi = 4 ft'/lbm. At section 2: Az = 2 ft, p2 = 0.20lb/ft, Uz = 120 fpm. Calculate (a) the mass flow rate, and the (b) change of mass stored in system,Am. %3D %3D tbm Ans. (a.) m = 15,000 &m2 2880- (b.) 12 120 %3D %3D hr hr hr