A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d2 of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d, of the tube is equal to T = T3 = 1000 lb-in. 800 lb-in. 500 lb-in. 500 lb-in. 800 lb-in. T = TA= Ts = B D C d2 = 1.0 in. 0.697 in

A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions shown below. The tube has an outside diameter d2 of 1.0 in. Given that the allowable shear stress is 12 kši, then the maximum permissible inside diameter d, of the tube is equal to T = T3 = 1000 lb-in. 800 lb-in. 500 lb-in. 500 lb-in. 800 lb-in. T = TA= Ts = B D C d2 = 1.0 in. 0.697 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
Weight at B = 40kn and at C is 30Kn
help me asap pls :((
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
i need solution thanks
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that di =50 mm and d2 =30 mm, find the average normal stress at the midsection of (a) rod AB (b) rod BC A 300 mm -d, В 5OKN 150 mm 30KN
A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=79, T2 =14, T3 =23 Note: round off your answer to whole number T2 Nm | T3 Nm T1 Nm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm