A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a compressive load of 0.75 MN as shown in the figure and the stress in the column is limited to 55 MPa, Calculate the desirable wall thickness of the column given that the diameter of the outside wall is 25 cm. Column Base plate

A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a compressive load of 0.75 MN as shown in the figure and the stress in the column is limited to 55 MPa, Calculate the desirable wall thickness of the column given that the diameter of the outside wall is 25 cm. Column Base plate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel column of hollow circular cross section shown in Figure is supported on a circular steel base plate and concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN.a. Determine the bearing stress induced by the column to the base plate in MPa.b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.
1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square cross section and bar width is 15 mm. Points A, B and C are pin connections. Square 15 mm side 6m 3.5m C 20KN
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each ?rod if Es=210 GPa and Ec=83 GPa Copper rod- 2 m Steel rod. -1 m- 1 m 2m -1 m- B 20 KN
3. A rectangular solid bar of width 20mm and depth 35mm is subject to a pure positive moment of 450Nm. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line. 4. The bar in Q3 is also subject to a tensile load of 15kN applied at the centroid of area. Calculate the stress in the bar and sketch the stress distribution through its thickness along the centre line.
The rigid bar of negligible weight is supported as shown in the figure. If W 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in-) a PF) E (GPa) Steel Rod 300 11.7 x 10 200 Bronze Rod 1400 18 х 104 83 Bronze 3 m Steel 1.5 m →| 1.0 m- 2.5 m +1.5 m W
A uniform concrete slab of total weight W is to be attached, as shown in the figure, to two rods whose lower ends are on the same level. Determine the ratio of the areas of the rods so that the slab will remain level. Figure P-215 Steel E - 29 x 10 psi Aluminum E - 10 x 10 psi L- 4 ft L-6R Total Weight = w 3 ft 6 ft The value of the load P at the aluminum 0.33 W b. 0.67 W с. W d. none of the above The ratio between the internal reactions of the aluminum and the steel 2.03 b. 0.49 c. 0.67 d. none of the above The ratio between area of steel and area of the aluminun 0.867 b. 0.409 c. 0.258 d. none of these If the value of W is limited to 1500 lb, which of the statements is true? The maximum load the steel can carry is greater than of the aluminum The maximum load the aluminum can carry is greater than of the stell The sum of loads at the steel and the aluminum is twice the value of steel The deformation developed at the steel is greater than that of aluminum If the cross-sectional area…
2. A 2-in.-diameter steel tube with a wall thickness of 0.05 inch just fits in a rigid hole. Find the tangential stress if an axial compressive load of 3140 lb is applied. Assume v=0.30 and neglect the possibility of buckling. data: 2 in Rod Wall Rod Vill
The frame in the figure is made of bars that have a square (solid) cross section of 3 cm on each side. A load of 5 kN is applied to the reinforcement. a) Draw the FBD of the reinforcement indicating the forces in each bar b) Calculate the stresses in each bar (don't forget to indicate if these are compressive stress or tension) c) Calculate the deflection of the bar AB if it were made of steel with E = 200 GPa
As shown in the figure, a column has a 10-inch by 10-inch cross section. A compressive load P with magnitude of 250 lb is applied. Determine the compressive normal stress at the cross section “a” (fc). Calculate final stress values and units
(c) The cross section of a quarter circular concrete block XYZof width 1.8m is shown in Figure 3. The specific weight of the concrete mix is 24 kN/m3. The hinge is along XX. Calculate the vertical force R at Y to hold the gate in this position. K Fixed slab 1.2 m Y W Fy 1.3 m FĦ D B Figure 3