A helical compression spring made of a wire of circular cross-section is subjected to a compressive load. The maximum shear stress induced in the cross-section of the wire is 24 MPa. For the same compressive load, if both the wire diameter and the mean coil diameter are doubled, the maximum shear stress (in MPa) induced in the cross- section of the wire is

A helical compression spring made of a wire of circular cross-section is subjected to a compressive load. The maximum shear stress induced in the cross-section of the wire is 24 MPa. For the same compressive load, if both the wire diameter and the mean coil diameter are doubled, the maximum shear stress (in MPa) induced in the cross- section of the wire is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A point in beam experiences a tensile stress (due to bending) of 50 N/mm2 and a shear stress of 20 N/mm2. The principal stresses are:
A rectangular beam subject to a pure negative bending moment will experience: Positive maximum normal stress at the top Positive maximun normal stress at the centroid Zero nomal stress at the top and bottom Positive maximum normal stress at the bottom
The compound shaft has a uniform cross-sectional area with the given length of each segment. Using the applied torque on the indicated position, determine the safe diameter of the shaft if the allow stress in each segment is shown and the free end angular deformation is limited to 2.8° Hint: 3 different diameters from stress analysis One answer of diameter from angular deformation. 90DN-m A Treactuon 75DN/m 1200N-m 3.4m 15m 2.3m Allow Torsional Segment Stress G 70 Gfa AB 89GPA BC 28GP. CD GOMPA 75 MPa 50 MPa'
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A circular aluminum tube subjected to pure torsion by torque T (see figure) has an outer radius r, equal to 1.5 times the inner radius r,. T (a) If the maximum shear strain in the tube is measured as 460 x 10-° rad, what is the shear strain y, (in radians) at the inner surface? rad (b) If the maximum allowable rate of twist is 0.126°/m and the maximum shear strain is to be kept at 460 x 10-6 rad by adjusting the torque T, what is the minimum required outer radius (r..min' in mm)? mm
A 180-mm length of 30 x 40 mm solid rectangular bar is loaded as shown in the diagram. The right end of the tube is fixed to a rigid frame while the left end is free. (a) Draw the stress element for point B at the top center of the bar (right end) and label the stress vectors acting on the element, including the stress magnitudes. (b) Draw the stress element for point C at the middle of the front face of the bar (right end) and label the stress vectors acting on the element, including stress magnitudes
Mechanics of deformable bodies.
answer pls in hand written solution
If the material is machine steel having a yield stress of sY = 500 MPa, determine the factor of safety with respect to yielding if the maximum shear stress theory is considered.
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = mm AD= i mm
A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 150mm and the wall thickness is 9mm. If the air in the tank is pressurized to 15.2MPA, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: (a) Ojong = i MPa Onoop = MPa (b) Tmax i MPa (c) Tabs max = MPa i