1) The plastic polymer cylindrical pipe is carrying flowing water at 0.5 N/mm pressure. The pipe has open ends. The inner diameter of the pipe is 0.1 m. The thickness of the pipe is one tenth of the pipe's inner radius. Calculate the stresses to show the state of stress in the walls of this pipe. (Suggested time for solution is 15 minutes)

1) The plastic polymer cylindrical pipe is carrying flowing water at 0.5 N/mm pressure. The pipe has open ends. The inner diameter of the pipe is 0.1 m. The thickness of the pipe is one tenth of the pipe's inner radius. Calculate the stresses to show the state of stress in the walls of this pipe. (Suggested time for solution is 15 minutes)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel rod of 15- mm diameter is held snugly (but without any initial stresses) between rigid walls by the arrangement shown in the figure part (a). (For the steel rod, use α = 12 x 10-6/˚C and E = 200 GPa.) Calculate the temperature drop ΔT (degrees Celsius) at which the average shear stress in the 12 – mm diameter bolt becomes 45 MPa. Also, what is the normal stress in the rod? What are the average bearing stresses in the bolt and clevis at A and between the washer (dW = 20mm) and wall (t = 18 mm) at B? If the connection to the wall at B is changed to an end plate with two bolts (see figure part b), what is the required diameter db of each bolt if the temperature drop is ΔT = 38˚C and the allowable bolt stress is 90 MPa?
Stress
S=25
d) Find the stress (in psi) induced in the aluminum tube by the temperature change.
Situation 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. Steel A = 550 mm² 10. Compute the axial stress at the bronze 11. Compute the axial stress at the aluminum 12. Compute the axial stress at the steel 60 KN 3.0 m Aluminum A = 400 mm² 2.0 m Bronze A = 220 mm² 20 KN 1.0 m 30 kN
An 8-mm thick steel tank has an outside diameter of 600 mm. It is internal pressure of 2.40 MPa. Determine the maximum subjected to stress in the tank. an
A solid steel bar 50 mm in diameter and 1.5 m long is secured between rigid walls. If the stress in the bar is zero at 27°C, what will be the stress (MPa) in the bar when the temperature rises to 42°C? Use E 200 GPa and a = 12.5 x 10-6 m/m-°C.
Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A and loaded as shown. Which of the following gives the maximum average normal stress in the system shown? 6P 4P A5.5 P/A B.4.5 P/A 3A 2A A 3P C.4 P/A D.3 P/A 4P 6P Which of the following is the highest value of stress within the strain hardening region of a typical elasto-plastic material subjected to tensile test? A. Elastic Limit B.Yield Stress C.Ultimate Stress D.Proportional Limit What is the lateral strain of a uniaxially loaded member if its longitudinal strain is 0.02 and its Poisson's ratio is equal to 0.3? A.+0.006 B.-0.006 C.+0.667 D.-0.667 Which of the following is the highest value of stress within the elastic region of a typical elasto-plastic material subjected to tensile test? A.Yield Stress B.Elastic Limit C.Ultimate Stress D.Proportional Limit
A solid aluminum (E = 70 GPa] rod (1) is connected to a solid bronze (E = 93 GPa] rod (2) at flange B, as shown. Aluminum rod (1) has an outside diameter of 34 mm and bronze rod (2) has an outside diameter of 16 mm. The normal stress in the aluminum rod must be limited to 139 MPa, and the normal stress in the bronze rod must be limited to 103 MPa. Assume L1 = 166 mm and L2= 359 mm. Determine: (a) the maximum downward load P that may be applied at flange B. (b) the deflection vg (downward is positive) of flange B at the load determined in part (a). C L2 B P. (1)
Full solution.
The tank shown in the Figure below is fabricated from a 10-mm steel plate. If the internal pressure in the tank is 1.2 MPa, calculate the tangential stress in the tank in MPa? ... 400 mm 600 mm
A 10mm thick cylindrical steel tank has an outside diameter of 650 mm. It is subjected to an internal pressure of 2.8 MPa. Find the tangential stress on the tank.