A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F.0.02 in.14 in.18 in.BronzeA = 2.4 in?E = 15 × 10 psia = 12 x 10-6/°FAluminumA = 2.8 in?E = 10.6 x 10 psia = 12.9 x 10-6/°FDetermine the temperature at which the normal stress in the aluminum rod will be equal to -9 ksi.The temperature of the aluminum rod is| °F.

Given data: gap=0.02 inTCold=75°FσA=-9 ksi Need to determine the temperature of the aluminum rod.

A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. 0.02 in. 14 in. 18 in. Aluminum A = 2.8 in? E = 10.6 × 10 psi a = 12.9 x 10-6/°F Bronze A = 2.4 in? E = 15 × 10® psi a = 12 x 10-6/°F %3D Determine the temperature at which the normal stress in the aluminum rod will be equal to -9 ksi. The temperature of the aluminum rod is | °F.

A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. 0.02 in. 14 in. 18 in. Aluminum A = 2.8 in? E = 10.6 × 10 psi a = 12.9 x 10-6/°F Bronze A = 2.4 in? E = 15 × 10® psi a = 12 x 10-6/°F %3D Determine the temperature at which the normal stress in the aluminum rod will be equal to -9 ksi. The temperature of the aluminum rod is | °F.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the figure, when the temperature was 24 ° C, a 0.5 mm gap was left. Determine the approximate value (° C) of the required temperature so that the normal stress in the aluminum bar is 75 MPa.
PLEASE ANSWER QUICKLY
PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10°/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa α = 17.3 x 10/°C
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 140°C. Determine the normal stress in the aluminum rod. Determine the change in length of the aluminum rod.
The two angle bars are used to support a tensile load "T". Assume the tensile load to be equally resisted by each angle. 400 mm x 20 mm THK Gusset Plate The steel used is L 6 x 6 x 1. Properties: A = 7096.76 mm? y = 47.244 mm Fy = 248 MPa Fu = 400 MPa b = 152.4 mm b. t = 25.4 mm x = 47.244 mm Effective hole diameter = 25 mm y Use case 2 for shear lag factor. Use NSCP 2015 code. 1. Determine the maximum allowable load that can be carried by the two L6 x 6 x1 based on yielding of the gross section--- 2. Determine the maximum factored load that can be carried by two L6 x 6 x 1, based on the fracture of the effective net area.---- 3. Determine the maximum allowable tensile load that can be carried.------ 4. Determine the maximum factored tensile load that can be carried-- bo
7m 4 m 4m 4 m 4m 150 kN 100KN 120KN Determine the normal stress in member BC if the section is circular having an outside diameter of 70mm w/ a thickness of 5mm and indicate if the member is in Compression or Tension.
Please solve urgently
The state of stress at a point in a member is shown on the rectangular stress element in (Figure 6) where the magnitudes of the stresses are |σx|=19 ksi and |σy|=14 ksi. Determine the state of stress on an element rotated such that the +x′ axis is 40∘ below the −x axis of the original stress element. Answer should be as σx′=, σy′=, τx′y′= in ksi
-8 in.- -8 in.- (a) (b) Which of the following best explains why cylinder (b) has a higher longitudinal stress in its walls compared to cylinder (a)? Assume the gauge pressure of the fluid inside the cylinder is non-zero. O Cylinder (b) is supported at two locations Cylinder (a) is not free to deform in its longitudinal direction The vertical (longitudinal) pressure in cylinder (a) is transferred directly to the [bottom] support, bypassing the cylinder walls None of the above the longitudinal stress for both cylinders is the same
In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x106 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm F 千 100mm 300mm (2) 6kN 400mm
10 ft 7.5 in 400 lb 400 lb 30 3.5 in The wood grain the tension member above are oriented approximately 30 degree to horizontal. Which of the following is closest to the magnitude of shear stress acting parallel to the grain? O11.4 psi O3.81 psi O 15.2 psi 6.60 psl
Please full solution with the drawing. Big and clear handwriting