A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm left and 60mm north of the center of gravity and induces a stress of 1.75 MPa compression at point A.  a) What is the axial load at Q in kN b) What is the stress induced at point C & D in MPa

Q: Q1: Considering the forces acting on the bar having solid circular cross-section, and an elastic…

A:

Q: Given force F-800 N and section AB is a bar with a diameter d = 0.05 m. Determine the internal…

A: Given :Force, F=800 NDiameter, d=0.05 mSut= 350 MP aSuc= 550 MP aWe have to identify the bending…

Q: mum weight of cylinder th your answer in two decimal

A: given:

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: GIVEN DATA A COMPOSITE ROD  AXIALLY LOADED GIVEN WE HAVE TO FIND STRESS IN EACH ROD Load P=3800lb…

Q: rce components at that point and show them on the figure b) identify the stress components at this…

A:

Q: Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure…

A: Data given -  P = 9 MPa  r = 150 mm  Or d = 2 × r = 2 × 150 = 300 mm  t = 9 mm

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data  height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: Question 2)  arm of Figure  B  from point x z  plane, a horizontal angle of θ = 38 ° angled F = 29…

A:

Q: The solid rod shown in the figure has a radius of 0.75 inches. Determine the state of stress at…

A: Part B.) the rod is loaded with a force of 800 lb as shown in the bottom figure.

Q: Problem I. In a high-rise building construction, a boom is being used to efficiently transport…

A:

Q: Module 4 Stress Distribution Point loads of 2000, 4000, and 6000 Ibs act at points A, B and C…

A:

Q: The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column…

A: Given data;- Outer diameter =4 in. Inner diameter = 3.5 in Square plate dimension = 7 in the column…

Q: Q2 a) Define the term of the neutral axis. b) The steel rod having a diameter of 20 mm is subjected…

A: Given: Diameter, d=20 mmM=400 N-m

Q: ximum tensil X1

A: given:length l=400mmthickness b=20mmdepth d=80mm

Q: A horizontal force P= 110,976 N is pushing an inverted L-frame supported by a foundation at the…

A:

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm…

A: Find the stress at point C and D and also find the value of force Q.

Q: The "C" clamp shown in the following figure has a rectangular cross section at location "a-a" with a…

A:

Q: Determine the stress in member KE for the truss loaded and supported as shown in figure (2). Note…

A: Truss is a structure which consists of many members and these members are pin jointed so that the…

Q: Problem 2: A pressure vessel with p = 200 psi internal pressure is subjected also to a twisting…

A: Given data, Applied internal pressure, P = 200 psi Applied twisting moment, T = 450 kips Internal…

Q: 1025 steel hold firmly 60 °C, there is a long It is heated from 20 c to Assume from both ends.…

A: Heat transfer is the form of energy that transfers from one system to another system by virtue of…

Q: PART 2 : COMPUTE THE AXIAL STRESSES IN ALL MEMBERS OF THE TRUSS SHOWN. USE 300 sq. mm AND 250 aq. mm…

A: Remark: As per the guidelines only the first three subparts will be answered. You can ask other…

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

A:

Q: Hertz contact theory can be used to determine the stresses due to contact between two spheres, which…

A: It is asked to find the stress by using Hertz contact theory

Q: Just for checking determine if true or false 1.) Tensile force tends to cut the body in two. 2.)…

A: given; 1.) Tensile force tends to cut the body in two. 2.) FBD is a sketch of the isolated body…

Q: 2.) Solve for the normal stress of rod AB with a diameter of 10mm if the block has a mass of 40kgC…

A:

Q: 1. Determine the maximum shear stress acting at section a-a of the cantilevered strut; L₁ = 1 ft, L2…

A: The objective of the question:Determine the maximum shear stress acting at section a-a of the…

Q: arm of Figure  B  from point x z  plane, a horizontal angle of θ = 38 ° angled F = 29 kN force sized…

A: Given data, The angle θ=38° Applied Force, F = 29000 N  Applied moment, M = 17000 N-m Length of arm…

Q: Q2- Show the stress components of a point in plane stress on the square in Figures below: Orr = 27…

A:

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of…

A: σBD=200 MPaLbd=48 mmhbd= .95 ma Now link BD σBD=P1AP1=200×π4×482P1=361.911 KNNow taking moment…

Q: Using the figure and loadings given, find the forces in all members, then find the average normal…

A:

Q: Find stress in each segment. Diameter of AB is 2in and diameter of BC is 1in.

A:

Q: A building weighing 100,000 Ibs is placed on the L-shaped slab shown. The soil below the basement is…

A: We know that, x=A1x1-A2x2A1-A2 A1=80×60=4800 ft2x1=802=40'y1=602=30' A2=50×20=1000…

Q: ness of 20 mm and the force P = 3 kN acts along the centerline of this thickness such that d = 150…

A: The area and the moment of inertia is-The distance of the top and bottom fiber from the centroidal…

Q: 41.M A shelf is being designed to hold crates having a to- tal mass of 1840 kg. Two support rods…

A: The mass of shelf is .The diameter of the rod is .The number of rod is .

Q: A smooth-walled 100 mm edge steel bucket is filled with rubber to form a rubber bucket embedded…

A: Given data: a=100 mmF=100 kNE=4 MPav=0.45 Need to determine the normal contact stress between the…

Q: A circular rod of diameterd and length 3d is subjected to a compressive force F acting at the top…

A:

Q: C 800 mm 18 mm dia. Rectangular bar B D 16 mm thick 25 mm 400 mm A F - F -800 mm

A: Given Data The force given is: 24 kN The height of the complee member is: 1200 mm The thickness of…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.