Problem 1. The joint is subjected to a force of 250 lb as shown. The member has a rectangular cross section of width 0.5 in. and thickness 0.75 in. a) Sketch the normal-stress distribution acting over section a-a. b) Determine the position of the Neutral Axis relative to the Centroidal Axis. c) Determine the state of stress at points A and B, include both combined normal stress and shear stress, and sketch the results on differential elements located at these points. Give special attention to the plane the stress components act and the directions.

Problem 1. The joint is subjected to a force of 250 lb as shown. The member has a rectangular cross section of width 0.5 in. and thickness 0.75 in. a) Sketch the normal-stress distribution acting over section a-a. b) Determine the position of the Neutral Axis relative to the Centroidal Axis. c) Determine the state of stress at points A and B, include both combined normal stress and shear stress, and sketch the results on differential elements located at these points. Give special attention to the plane the stress components act and the directions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need it handwritten and correct or skip please only handwritten handwritten handwritten handwritten otherwise dislikfor sure
Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively. Determine the axial stress in member CH in psi. (Numerical absolute answer only without units in 3 decimal places)
only HANDWRITTEN answer needed ( NOT TYPED)
5 Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an internal pressure of 60 MN/m² and an extemal pressure of 30 MN/m?. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches.
3. The aluminum block has the rectangular cross-section and is subjected to an axial compressive force of 8 kips. The 1.5-in side changed its length to 1.50014 inches. Use E = 10 x 10³ ksi. Calculate the new length of the 2-inch side. Answer: Lnew = 2.00019 in 1.5 in 2 in. 8 kip- 8 kip 3 in. 4. A solid cylinder of diameter D is subjected to an axial load P. Show that its change in diameter is 8D = 4Pv/лDE.
Hertz contact theory can be used to determine the stresses due to contact between two spheres, which can be used approximate frictionless contact between the patellar and femoral components of a total knee replacement. Part a) Show on a sketch how the stresses at the surface vary from the centre of contact to the edge of contact. Part b) Make a sketch of an infinitesimal element of material at the centre of contact that shows the stress components. Identify the maximum principal stress, and write an expression for the maximum shear stress. Part c) Sketch a graph that shows how the maximum contact pressure varies with load and in a sentence explain why the curve has the shape it does.
Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the other four pins has a 16mm diameter. a. Determine the maximum value of the average normal stress in the links connecting points B and D and points C and E. b. Determine the average shearing stress in points B and C.
answer item 2 only Diameter 100.5mm thickness 10.25 mm axial stree 451 mpa
a. Determine the principal stresses at point A on the cross section of the wrench at section a-a. Also Specify the orientation for this state of stress. b. Determine maximum in-plane shear stress at point A on the cross section of the wrench at section a-a. Also Specify the orientation for this state of stress.
Question 2) arm of Figure B from point x z plane, a horizontal angle of θ = 38 ° angled F = 29 kN force sized and C from the point z direction M = 17 kn.m acts a moment in size. The lengths of the arm are also given as L 1 = 1.5 m and L 2 = 1.1 m . It is desired to determine the stress state of point A on the aa section taken from the arm. The radius r of the section is r=0.015 m and the shear modulus of the arm material is also G = 78 Gpa . According to this; Question 2-C) Find the normal stress caused by the normal force at point A ( Write your result in MPa .) Question 2-D) Find the normal stress caused by the bending moment at point A. (Your result MPa in the size of your font.)
Question 24 A 3 m long hollow circular tube made from aluminium with an outside diameter 200 mm and a wall thickness of 10 mm is filled with a polymer matrix. It is subjected to a tensile axial force of 500 kN acting uniformly over the entire cross-sectional area of the filled tube. If the elastic modulus of the aluminium is E₂=75 GPa, and of the matrix is Em 15 GPa, calculate the normal direct tensile stresses acting on the two materials and the extension of the tube. = Which of the following answers is correct? The tensile stress in the aluminium is ten times larger than the tensile stress in the matrix The tensile stress in the aluminium is 45.2 MPa and the extension of the tube is 1.8 mm. The tensile stress in the matrix is 19.1 MPa and the extension of the tube is 3.1 mm. O The tensile stress in the matrix is 40.5 MPa and the extension of the tube is 2.5 mm. AMSUN The tensile stress in the aluminium is 54.7 MPa and the extension of the tube is 0.8 mm.
PROBLEM 3. A double-row butt joint is used as a connection. It is made up of two 210-mm by 20-mm cover plates and 210-mm by 35-mm main plate. The plates are to be connected by 32-mm diameter rivets. The allowable stresses are 75MPa for shear, 90MPa for tension and 285MPa bearing. Assume that each hole is 3mm larger than the rivet diameter. ust PDF ng imen GIBL o Alel 1. What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for shear? 2. What is the largest value of P (kN) that can be applied without exceeding the ollowable stress for bearing? 3. What is the largest value of P (kN) that can be applied withour exceeding the allowable stress for tension? ng in