A footing measures 1.80m x 1.80m with reinforcement, x-bar 12 and y-bar 12. Compute the quantity of tie wires needed if length of each tie wire is 30cm and the number of footing is 12. Write numerical values only. Use 2 decimal places. %3D

A footing measures 1.80m x 1.80m with reinforcement, x-bar 12 and y-bar 12. Compute the quantity of tie wires needed if length of each tie wire is 30cm and the number of footing is 12. Write numerical values only. Use 2 decimal places. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Yult CNC 3.4ult 1.3N. + qNg 0.4YBNY 11. are non- biodegrable polymeric used in various construction…

A: b. Geosynthetics are non-biodegrable polymeric used in various construction projects by Geotechnical…

Q: A. For the three cases shown determine the factored moment, Mu, at the critical section. The qu,net…

A: To determine the factored moment at the critical section of the footing: Case 1: Masonry wall…

Q: athJax webview Q.1 A strip-footing is 60 ft long and 10 ft wide. The strip-footing has a rectangular…

A: Given:- L=60 ft W=10 ft 3 Columns bearing capacity of the soil =10000 kg/m2 To find:- shear force…

Q: In the following photo, identify the type of footing that is being installed. Photo C: Photo C:…

A: Given data in question Footing picture To find out Which type of footing is given in picture

Q: B AS-1 14 A A AS-2 TYPICAL FOOTING PLAN SCHEDULE OF FOOTING SIZES & REINFORCEMENT FOOTING SECTION…

Q: 3. Calculate the total load on a 4'x4'x1' spread footing that is buried 3' below, and a hot tub is…

Q: Design a square footing for a column 350x350 mm in section to carry a dead load of 330kN live load…

Q: 7. The rebar is to be lapped 18 inches.

A: Show the footing plan as in Figure (5-26) Show the footing plan as in Figure (5-27) Show the…

Q: A-1: In the previous part of this assignment, you were asked to find the size and depth of the FT3…

A: Following are the given information. Dimension of footing =6'×6'×1' 6" No of footing =8 Working…

Q: 9- Consider the following operations in Bridge shallow foundation construction: 1. Placing steel 2.…

A: Shallow foundations disperse impact load throughout vast regions of near-surface topsoil to reduce…

Q: Design a footing to support a BRICK wall with a dead load D= 120 kN/m and a live load L= 70 kN/m,…

A: S.NO DESCRIPTION VALUE 1 LIVE LOAD 2 DEAD LOAD 3 WALL THICKNESS 250 mm 4 BAR DIAMTER…

Q: Using a waste factor of 7 percent, determine the number of cubic yards of concrete needed to pour…

Q: 1. Draw the isometric section detail of a concrete footing having a size of 1200 mm x 1400 mm with a…

A: Dimension of foundation = 1200mm x 1400mm Dimension of column = 200mm x 300mm

Q: The detail drawings of the concrete footings for a building are shown below. The bars to be ordered…

A: Data given Bars to be ordered = 16 mm ϕ × 6 m Value to be calculated for =15 footings Footing…

Q: 8700 a. Estimate the size of the foundation/footing under assigned column using LOAD TAKE DOWN…

Q: scuss what is a cantilevered footing and a continuous footing.

A: Cantilever footing It's a type of foundation in which two or more columns are connected by a rcc…

Q: Design the largest interior and edge panel of the slab for the plan system shown below (Follow the…

Q: A 100lb block with a wide base is pulled by a force P and us=0.4. Which force orientation requires…

Q: 5.3 A short steel column supports an axial compressive load of 120,000# and is welded to a steel…

A: Axial compressive load = 120,000 lbAllowable bearing on concrete = 450 psiAllowable soil pressure=…

Q: Submit the following online or on paper: The footing below is a 5ft square. The soil immediately…

A: The unit weight of the soil above the footing, The unit weight of the soil below the footing, The…

Q: Explain pile, caisons(well foundation) ?

A: Pile foundation: A pile foundation is defined as a deep foundation that is used to transfer the…

Q: Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the…

Q: Compute the A) analysis of loads B)total downward load and C) base area of the footing

A: Given: Dead loads Live loads Cross-section of square footing =…

Q: Determine the total quantity of reinforcement for cross section shown below Combined footing of L=…

Q: Square column size - 16" PDL 280 kips, PLL 180 kips L = 1.5B, fy = 60 ksi, f'c = 4000 psi fa 4 ksf,…

A: Square column size- 16''PDL= 280 kipsPLL=180 kipsL=1.5Bfy=60 ksif'c=4000 psifa=4 ksfFooting base-…

Q: 1-Write down the important purpose of providing the foundation.

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Calculate the Load distribution of slabs to beams 2, C and D using 10kPa load multiplied by the…

A: First we have to divide the slab area in to different parts. Then multiply the area around that…

Q: Overall depth of corbel at the outside edge of the bearing area shall be at least * O 0.6 d O 0.6 b…

Q: Calculate the SFCA of formwork necessary to install 71 linear feet of a continuous footing that is 3…

A: Given data - Length of footing L = 71 feet Width B = 3 feet Height h = 1 feet Find out - The SFCA of…

Q: A combined footing carries two columns with the following information: The edge of the left column…

Q: Q2) For the column layout shown in Figure (2), find the plan dimensions of a combined footing and…

A: Solution; The values provided in the question are as follows: Soil allowable bearing capacity…

Q: Define Equivalent Uniformly Loaded Footing

A: Footings are a very important part of the foundation. They are constructed with the help of concrete…

Q: Problem 2: Find the Area and volume of the footings shown below. Use the center line method to…

A: The total length of the center line of the wall should be determined.Then the area of the footings…

Q: In the following photo, identify the type of footing that is being installed. Photo B: Photo B:…

A: To find which type of fitting is shown in figure-

Q: The gross allowable soil pressure is 100 kPa and width of the wall is 200mm. Assume that the top of…

A: The bearing capacity of soil is defined as the capacity of the soil which will bear the loads or we…

Q: The gross allowable soil pressure is 100 kPa and width of the wall is 200mm. Assume that the top of…

Q: By using Ultimate Strength Design Method, design the slab showing in the figure below for the…

A: In the event that length and width ratio, the extent is more conspicuous than or comparable 2 or…

Q: What would be the amount of concrete in cubic yards required for the footing below assuming a depth…

A: length of footing is

Q: • Determine the bearing stress (in ksi) between the steel base plate and the concrete footing. Do…

A: Bearing stress is normal stress felt by footing due to applied load over it. Bearing stress =…

Q: Calculate the quantities of RC for (PC, footing, and tie beam) and reinforcement steel required for…

A: Here's what I can analyze from the image:Footing Dimensions:Two separate footings are indicated,…

Q: Given ten (10) units of isolated rectangular footing, 1.20m x 2.00m x 0.30m, reinforced with 10pcs…

A: Rates are taken from CPWD DSR

Q: A COLUMN Fcomm x 500mm AT CENTER OF A 3m x 3m FOOTING SUPPORTS A DEADLOAD OF 928 ION AND A LIVELOAD…

A: Answer (a) Calculation of minimum soil pressure We know that minimum soil pressure is given by qmin…

Concept explainers

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.

Question

A footing measures 1.80m x 1.80m with
reinforcement, x-bar 12 and y-bar = 12.
%3D
%3D
Compute the quantity of tie wires needed if
length of each tie wire is 30cm and the
number of footing is 12. Write numerical
values only. Use 2 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

provide complete solution
A 2-foot square footing has its bottom 2.12 ft. below the ground surface. The ground water table is located at a depth of 4 ft. below the ground surface. Unit weight of soil is 118 lb/ft3, Saturated unit weight is 123 lb/ft3, cohesion = 98 lb/ft2. Use angle of internal friction = 30° (Nc = 35.3, Nq = 29.1, begin mathsize 12px style text N end text subscript straight gamma end style = 19.1). Compute the allowable load (in lb) that the footing could carry. Use FS = 2.7. Round off to the nearest whole number.
Calculate the Load distribution of slabs to beams 2, 3 and A using 10kPa load multiplied by the tributary width. Yellow represents columns. Red represents beams.
Why is the sum of un factored load instead of the factored load used for determining the width of the footing?
Problem 2. Twenty pieces of the footing shown below are to be used for a building project. Estimate the steel reinforcing bars required if the length of the bars to be ordered is 6.060 meters. 0.60M COLUMN 1.20M PLAN OF FOOTING 3-Ø16MM BARS 6-Ø12MM BARS FOOTING COLUMN BARS COLUMN COLUMN TIES 3-Ø16MM BARS 6-Ø12MM BARS (TYPICAL) 0.30M www. w SECTION OF FOOTING
Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the tributary width. Colored box represents columns and uncolored represents beams.
Explain the concept of equivalent footing method.
I'll upvote if complete and correct. Thank you. Don't answer this if you already answered or get downvote.
Need Complete an elaborate solution Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete fc’ = 25MPa and ASD.
15. A contractor is building thirty-two (32) of the 2'- 0"x 2'- 0"x 0"-10" spread footings shown in the drawing below. Using the material schedule at the bottom of the page, answer the questions a to f below. Concrete (cy) • Rebar (lbs) 2 x 12 Forms 2 x 4 stakes (each) • Nails (lbs) "x12" CF Plan View 2-37 Side View (2) #4 brach way top and botto ▲ Section A-A Concre "x12" Concrete Farm 2"x4" 2-6 Side View Material Specification Frequency Waste, of Use % Concrete 4,000 psi 1 3 Rebar # 4 (0.668 lbs/lf) 1 10 Forms 2 x 12 in. x length 4 10 Stakes Oak, 2 x 4 x 18 in. 4 25 Nails 3½ in. common 1 10 2-67 2x 12" Conte Form 4x4 Sales Concrete (2) reach way top and bott 2-3 Section A-A Comments Use exact measurements then add waste 2" clearance from ends to forms Use exact measurements then add waste Total length is 18" 1 lb/100 bf of total lumber (forms plus stakes)
Determine the SFCA of forms needed for the continuous footings shown below. 30' 18' 40" 1' #4 REBAR @ 12" O.C. BOTH WAYS 12' #5 DOWELS @ 12" O.C. ALTERNA TING 1'-3" DIRECTIONS #4 REBAR @ 12" 0.C. 1'-3" 5 EACH #4 CONT. REBAR 3'
I'll upvote if unique and complete. Don't answer this if you already answered or downvote. Thank you