A-1: In the previous part of this assignment, you were asked to find the size and depth of the FT3 footing. The dimension of the footing was 6' x 6' x 1'-6" deep. The bottom of the footing was also 8' deep. On the drawings, there are 8 EACH of these footings. 6. 7. When digging the hole to install this footing, you will need to dig the hole 2¹ bigger on all sides of the footing for working space. This would make the excavation 10' x 10'. What is the volume of dirt that will be excavated for these 8 footings? Remember, when you determined the cubic feet, divide by 27 to convert from cubic feet to cubic yards. 3 points To calculate the forms needed for the FT3 footing, you need to calculate the SURFACE AREA of each side of the footing and add four values together. What is the square footage of forms needed to pour these 8 footings? 3 points

A-1: In the previous part of this assignment, you were asked to find the size and depth of the FT3 footing. The dimension of the footing was 6' x 6' x 1'-6" deep. The bottom of the footing was also 8' deep. On the drawings, there are 8 EACH of these footings. 6. 7. When digging the hole to install this footing, you will need to dig the hole 2¹ bigger on all sides of the footing for working space. This would make the excavation 10' x 10'. What is the volume of dirt that will be excavated for these 8 footings? Remember, when you determined the cubic feet, divide by 27 to convert from cubic feet to cubic yards. 3 points To calculate the forms needed for the FT3 footing, you need to calculate the SURFACE AREA of each side of the footing and add four values together. What is the square footage of forms needed to pour these 8 footings? 3 points

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What are the two, independent design criteria all foundations must satisfy? Select one or more: O a. Appearance b. Bearing Capacity c. Settlement O d. Depth
Q2. If you were, ask to concrete 2mx2m foundation of 400mm depth with column of 300mm x 200mm and 1500mm height and you need to list all the WBS for such footing. Answer the flowing: 1. Sketch this footing using scale 1:100 fuorle
A footing measures 1.80m x 1.80m with reinforcement, x-bar 12 and y-bar = 12. %3D %3D Compute the quantity of tie wires needed if length of each tie wire is 30cm and the number of footing is 12. Write numerical values only. Use 2 decimal places.
Define the term Floating Foundations.
Given: How much concrete will you need for a 32' x 52' x 6" slab pour supported by a 3' deep x 18" trench wall and 1'x 3' trench footings. Stem wall/footings will be formed around the periphery of the slab & w/in two interior grade beams. For a w/c of 0.5, what is the weight of cement and water? Assume the wet weight of the concrete is 137 Ibs/ft3, water is 62.4 lbs/ft3 and M15 mix. Solution: ?
Explain the conditions for assumed to determine seismic bearing capacity for strip foundations.
Discuss the placement of equivalent footing for various soil conditions.
Problem 2. Twenty pieces of the footing shown below are to be used for a building project. Estimate the steel reinforcing bars required if the length of the bars to be ordered is 6.060 meters. 0.60M COLUMN 1.20M PLAN OF FOOTING 3-Ø16MM BARS 6-Ø12MM BARS FOOTING COLUMN BARS COLUMN COLUMN TIES 3-Ø16MM BARS 6-Ø12MM BARS (TYPICAL) 0.30M www. w SECTION OF FOOTING
Wall footings are 0.4m wide, 0.2m thk, 0.6m deep from NGL, with 2-inch thick gravel bedding. How much gravel is needed for gravel bedding of Wall Footings? Select the correct response: 1.2 cu.m. 0.6 cu.m. 0.4 cu.m. 1.0 cu.m.
Explain the concept of equivalent footing method.
If the post is to be erected in a medium clay [maximum soil bear capacity is 250 kPa], and will be placed on top of a square footing weighing 25 kN, what will be the minimum dimension of the footing?
Determine the SFCA of forms needed for the continuous footings shown below. 30' 18' 40" 1' #4 REBAR @ 12" O.C. BOTH WAYS 12' #5 DOWELS @ 12" O.C. ALTERNA TING 1'-3" DIRECTIONS #4 REBAR @ 12" 0.C. 1'-3" 5 EACH #4 CONT. REBAR 3'