A flanged bolt coupling consists of six 10-mm diameter steel bolts on a bolt circle 300 mm in diameter and four 10 mm diameter steel bolts on a concentric bolt circle 200 mm in diameter. When torque applied is 5500 Nm, find the shearing stress (MPa),  in the bolts found in the inner concentric circle.

Q: For the solid circular rods exposed to the shown torques, determine the segment that experiences…

A:

Q: A solid circular shaft needs to be designed to transmit a torque of 50N.m. If the allowable shear…

A: As given in question, Torque being transmitted = T = 50 Nm = 50,000 Nmm Allowable shear stress of…

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

A: Let shear modulus (G) of steel shaft be 83 GPa. The torque in AB and BC portion is -TAB=6000-2000 =…

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: Two 38.1 mm shafts are connected by a flanged coupling. The flanges are fitted with 6 bolts SAE 1020…

A: flanged coupling d=38.1mmn=6D=152.4mmN=260 rpmT=850000 Nm  =850000 ×103 Nmmfs=5Sult=430MPaSsy=330…

Q: A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm…

A:

Q: A compound steel [G = 80 GPa] shaft consists of a solid 86-mm-diameter segment (1) and a solid…

A:

Q: 8.5 (A). A flanged coupling having six bolts placed at a pitch circle diameter of 180 mm connects…

A: Given data  Diameter of pitch circle = 180mm Power = 80kW at 240 rev/min Allowable shear stress in…

Q: i kullanılmıştı ancı bölgesind

A: Given:  Power to be transmitted = 0.67 KW Rotational speed = 900 KPM Gear width = 20 mm Yield…

Q: PROBLEM 2 A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm.…

A:

Q: (7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the…

A:

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: A flanged bolt coupling consists of eight – 10mm diameter steel bolts on a bolt circle 500mm in…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 120 mm in diameter to a hollow shaft 100 mm…

A:

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

A:

Q: A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in…

A: The force on the shaft is 94236.5 N.

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm, a…

A:

Q: Identify the flange thickness (in mm) of a flange coupling having 6 bolts, that is 10-mm in…

A: Write the expression of torque transmitted to the flange. Tflange=nd1tfσcfD12      ......…

Q: A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as…

A:

Q: 2. A tube is made of aluminum ( G = 24 GPa ) and has a rectangular cross section as shown in figure.…

A:

Q: Compute the torque necessary to twist a 3/8 inch diameter solid rod of rolled brass, 12 inches long,…

A:

Q: A cast-iron pulley transmits 49 kW at 1,750 rpm. The shaft to which it is to be keyed is 44.4 mm in…

A:

Q: Design and draw a protective type of cast iror flange coupling for a steel shaft transmitting ? kW…

A: Machine Design

Q: The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a…

A:

Q: A B 55² 240 N.mm 420 N.mm 300 N.mm 480 N.mm Figure 1 - Torques applied to the driveshaft 1) DERIVE…

A: Find the  Angle of twist expression Shaft diameter Maximum shear stress

Q: hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate…

A:

Q: Please show complete work in handwritten format. Don't use chatgpt,If you use Chatgpt it will get a…

A:

Q: A flange coupling having 6 bolts, each 18 mm in diameter, is used to transfer the power of a 75-mm…

A:

Q: Two designs for a shaft are being considered. Both have an outside diameter of 60 m and are 800 mm…

A:

Q: A drive shaft running at 2500 rpm has outer diameter of 60mm and inner diameter of 40mm. The…

A:

Q: A flange coupling having six bolts on a pitch circle radius of 300 mm connects two hollow shafts…

A:

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm  D=41mmPCD=63mm

Q: A solid circular shaft needs to be designed to transmit a torque of 50N.m. If the allowable shear…

A: As given in question, Torque being transmitted = T = 50 Nm = 50,000 Nmm Allowable shear stress of…

Q: 3. A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to…

A:

Q: A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ…

A:

Q: Problem 3

A: Sign Convention: Consider anticlockwise torque as positive and clockwise torque as negative.Refer to…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.