A steel shaft 50 mm diameter and 500 mm long is subjected to a twisting moment of 1100 N-m, the total angle of twist being 0.6°. Find the maximum shearing stress developed in the shzaft and modhulus of rigidity.

Q: Design the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000…

A: Given data: The torque applied is, T = 1,000,000 lb-in. The shear stress developed, τ = 8,000 psi.…

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: A thin-walled tube is subjected to torsion as shown. Determine the angle of twist produced. (in rad)

A: Given Radius =300 mm = 0.3 m Length = 6 m Thickness = 25 mm = 0.025 m T = 4kN m = 4000 Nm G = 70 GPa…

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

A:

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when subjected to a torque…

A:

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

A:

Q: A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 lb, a horizontal shear…

A: Solution:

Q: For the cross-section shown below, computer the rate of twist and the shear stress if a torque of…

A: Torsion Torsion is a twisting of object when torque is applied on it.   Torque Torque is a…

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

A:

Q: A mild steel shaft of 50mm diameter is subjected to a bending moment of 1.9kNm. If the yield point…

A: Introduction The maximum shear stress hypothesis states that a material will fail or yield if its…

Q: (2) The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter…

A: Given data:Applied torque The diameter of the aluminiumThe diameter of the steelLength of the…

Q: a solid rod with a circular cross-secton is subject to a torque of 253 N.m. if diameter of the rod…

A:

Q: A solid shaft BC is fixed at the B end and subjected to torque T at the C end, as shown below. The…

A:

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the…

A: Given Data The diameter of the shaft is: d=8×10-3 m The length of the shaft is: L=200×10-3 m The…

Q: 2. The solid shaft AB has a diameter d_s = 1.5 in. and is made of steel with a shear allowa of 12…

A:

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.